background image

 

A-7

 

 CONTENTS 

 

 

1. Overview ....................................................................................................... 1 
2. Performance Specifications .......................................................................... 2 
3. Handing ......................................................................................................... 3 

3.1 Precautions for Handling.......................................................................... 3 

4. Part Identification Nomenclature ................................................................... 4 
5. Wiring ........................................................................................................... 5 

5.1 Precautions for Wiring ............................................................................. 5 
5.2 Wiring....................................................................................................... 5 

6. Outline Dimension Drawings ......................................................................... 6 

6.1 A1SJ71AS92............................................................................................ 6 

 

Содержание MELSEC-A A1SJ71AS92



















Отзывы: