Mitsubishi FDE125VNPWVH страница 84 Скачать руководство пользователя

Страница: 84 / 117

E37

Outdoor heat exchanger

temperature sensor anomaly

1. Applicable model

5. Troubleshooting

All models

Diagnosis

Countermeasure

Is the

outdoor heat

exchanger temperature

sensor connector

connected

properly?

YES

Are the

characteristics of

outdoor heat exchanger

temperature

sensor

OK?

For the characteristics of outdoor heat exchanger

temperature sensor, see the following graph.

YES

Temperature-resistance characteristics

Temperature sensor resistance (k

Ω

)

Temperature (°C)

Ω

at 25°C

(Broken wire)

(Short-circuit)

Correct connector.

Defective outdoor heat

exchanger temperature

sensor

➞

Replace.

Defective outdoor unit

PCB

➞

Replace.

(Defective outdoor heat

exchanger temperature

sensor input circuit)

2. Error detection method

Detection of anomalously low

temperature (resistance) on

the outdoor heat exchanger

temperature sensor

3. Condition of error displayed

•

When the temperature sensor

detects -55 °C or lower for 5

seconds continuously within

2 minutes to 2 minutes 20

seconds after the compressor

ON, the compressor stops. After

3-minute delay, the compressor

starts again automatically, but

if this anomalous temperature

is detected 3 times within 40

minutes.

• When -55 °C or lower is

detected for 5 seconds

continuously within 20

seconds after power ON

4. Presumable cause

• Defective outdoor unit PCB

• Broken sensor harness or

temperature sensing section

• Disconnected wire connection

(connector)

Note:

Error code

Remote control:

LED

Green

Red

Content

Indoor

Stays OFF

Keeps flashing

'22 • PAC-SM-412

Содержание FDE125VNPWVH






















































































































Результаты поиска

Содержание FDE125VNPWVH

Отзывы:

Похожие инструкции для FDE125VNPWVH

Бренды по названию

Популярные бренды

Mitsubishi FDE125VNPWVH, Руководство по обслуживанию

Результаты поиска

Содержание FDE125VNPWVH

Отзывы:

Похожие инструкции для FDE125VNPWVH

Бренды по названию

Популярные бренды