manualshive.com logo in svg

Mitsubishi FDE125VNPWVH, Руководство по обслуживанию, Страница: 30 / 117

Поделиться
Скачать
Mitsubishi FDE125VNPWVH Скачать руководство пользователя страница 30

'22 • PAC-SM-412

-

 29 

-

  (ii) Heating

1) Operating conditions

 

When the outdoor air temperature (TH2) is 13ºC or higher continues for 30 seconds while the compressor speed is other th

an 

0 rps

2) Detail of operation

 

 

After the outdoor fan operates at -3 speed for 60 seconds; the corresponding outdoor heat exchanger temperature shall impl

e-

ment the following controls.

a) Outdoor heat exchanger temperature 

=

< 10

ºC

 After the outdoor fan speed rises (up) to 1 speed for 60 seconds; if the outdoor heat exchanger temper-

 

ature is lower than 10

ºC

, gradually increase the outdoor fan speed by 1 speed.

b) 10

ºC

 < Outdoor heat exchanger temperature 

=

<

 13ºC

  After the outdoor fan speed maintains for 20 seconds; if the outdoor heat exchanger temperature is 10

ºC

-

13ºC

, maintain outdoor fan speed again.

c) Outdoor heat exchanger tempeature > 13

ºC

 

After the outdoor fan speed drops (down) to 1 speed for 60 seconds; if the outdoor heat exchanger temper-

 

ature is higher than 13

ºC

, gradually reduce outdoor fan speed by 1 speed. (Lower limit 2nd speed)

3) Reset conditions

When either of the following conditions is satisfied

a) The outdoor air temperature (TH2) is 11ºC or lower.

b) The compressor speed is 0 rps.

(f) Outdoor fan motor protection

If the outdoor fan motor has operated at 75 min

-1

 or lower for more than 30 seconds, the compressor and fan motor are stopped.

(a) Starting conditions (Defrost operation can be started only when all of the following conditions are satisfied.)

(i) After start of heating operation

 

When it elapsed 35 minutes (Accumulated compressor operation time)

(ii) After end of defrost operation

 

When it elapsed 35 minutes (Accumulated compressor operation time)

(iii) Outdoor heat exchanger sensor (TH1) temperature

 

When the temperature has been below 

－

5ºC for 3 minutes continuously 

(iv) The difference between the outdoor air sensor temperature and the outdoor heat exchanger sensor temperature (TH2-TH1)

 

●

 The outdoor air temperature 

≧

 

－

2ºC

 : 7

ºC

 or higher

 

●

 

－

15ºC 

＜

 The outdoor air temperature 

＜

 

－

2ºC

 : 4/15 × The outdoor air tempe 7

ºC

 or higher

 

●

 The outdoor air temperature 

≦

 

－

15ºC

 : 

－

5ºC

 or higher

-20

-20

-15

-10

-5

0

5

10

-15

-10

-5

0

Outdoor air temperature (

℃

)

Outdoor heat exchanger temperature (

℃

)

Defrost operation

start

Defrost operation start temperature

(v) During continuous compressor operation

 

In addition, when the speed command from the indoor control of the indoor unit during heating operation has 
counted 0 rps 10 times or more and all conditions of (i), (ii) above and the outdoor air temperature is 3

ºC or less 

and 

the temperature for outdoor heat exchanger sensor (TH1) is 

－

5ºC

 or less: 62 rps or more, 

－

4ºC

 or less: less 

than 62 rps are satisfied, defrost operation is started.

(4) Defrost operation

Содержание FDE125VNPWVH






















































































































Отзывы:

Нет отзывов