Mitsubishi Electric SUZ-KA25VA2 Скачать руководство пользователя страница 35

Страница: 35 / 74

[SUZ-KA25/35/50VA2.TH]

D Check of compressor winding

Disconnect the connector between the compressor and intelligent power module, and measure the resistance between the

compressor terminals.

<<Measurement point>>

at 3 points

BLK-WHT

BLK-RED

WHT-RED

<<Judgement>>

Refer to 11-4.

0 [

] ················Abnormal [short]

Infinite [

] ·······Abnormal [open]

NOTE

: Be sure to zero the ohmmeter before measurement.

Measure the resistance between the lead wires at 3 points.

E Check of compressor operation time

Compressor starts

Abnormal

(IPM failure)

(Compressor winding short)
Abnormal

(Compressor lock out)

(Starting defect)

Abnormal

(Poor contact,)

(Outdoor P.C. board defect)

(Disconnected connector)

Abnormal

(Refrigerant circuit defect)

(Closed valve)

Normal

0 second

1 second

2 seconds

10 seconds

10 minutes

<<Judgement>>

Thermistor

Symbol

Connector, Pin No.

Board

Defrost

RT61

Between CN641 pin1 and pin2

Inverter P.C. board

Discharge temperature

RT62

Between CN641 pin3 and pin4

Fin temperature

RT64

Between CN642 pin1 and pin2

Ambient temperature

RT65

Between CN643 pin1 and pin2

Outdoor heat exchanger temperature RT68

Between CN644 pin1 and pin3

Replace the thermistor except RT64.

When RT64 is abnormal, replace the inverter P.C.

board or the outdoor power board.

Replace the inverter P.C. board

or the outdoor power board.

Is the thermistor normal?

(Refer to 11-6-1. or 11-6-2. )

Reconnect the connector of thermistor.

Turn ON the power supply and press EMERGENCY OPERATION switch.

Does the unit operate for 10 minutes or more

without showing thermistor abnormality?

OK.

(Cause is poor contact.)

Yes

F Check of outdoor thermistors

Disconnect the connector of thermistor in the outdoor P.C. board (see

below table), and measure the resistance of thermistor.

Connect the compressor and activate the inverter. Then measure the

time until the inverter stops due to over current.

<<Operation method>>

Start heating or cooling operation by pressing EMERGENCY

OPERATION switch on the indoor unit.

(TEST RUN OPERATION : Refer to 11-5

<<Measurement>>

Measure the time from the start of compressor to the stop of

compressor due to overcurrent.

Содержание SUZ-KA25VA2











































































Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Mitsubishi Electric SUZ-KA25VA2, Техническое и сервисное руководство, Страница: 35 / 74

Результаты поиска

Содержание SUZ-KA25VA2

Отзывы: