Mitsubishi Electric SUZ-KA25VA2 страница 55 Скачать руководство пользователя

Страница: 55 / 74

m How to check miswiring and serial signal error

Turn OFF inverter-controlled lighting
equipment.
Turn OFF the power supply and then
turn ON again.
Press EMERGENCY OPERATION
switch.

•

Is serial signal
error indicated 6
minutes later?

Yes

Reinstall
either the unit
or the light
away from
each other.
Attach a

lter

on remote
control receiv-
ing section
of the indoor
unit.

•

Turn OFF the power supply.

Is there rated voltage in the power supply?

Yes

Turn ON the power supply.

Check the power supply.

Is there rated voltage between outdoor terminal block S1 and S2?

Check the wiring.

Press EMERGENCY OPERATION switch once.

Does the upper lamp of OPERATION INDICA-
TOR lamp light up? <Con

rmation of the power

to the indoor unit>

Yes

Is serial signal error indicated 6 minutes
later?

Yes

Is there any miswiring,
poor contact, or wire
disconnection of the
indoor/outdoor connect-
ing wire?

Yes

Correct them.

Turn OFF the power supply.
Check once more if the indoor/outdoor
connecting wire is not miswiring.
Short-circuit outdoor terminal block S2
and S3. 1

1. Miswiring may damage indoor electronic control P.C.

board during the operation.
Be sure to con

rm the wiring is correct before the opera-

tion starts.

Turn ON the power supply.

Does the LED on the inverter P.C. board repeat "3.6-second-OFF and 0.8-sec-
ond-ON quick blinking"? 3

Yes

(Lighted

or not

lighted)

Replace the inverter P.C. board. 2

2. Be careful of the residual voltage of smoothing

capacitor.

Turn OFF the power supply.

Remove the short-circuit between outdoor terminal block S2 and S3.

Yes

3. Be sure to check this within 3 minutes after turning ON.

After 3 minutes, LED blinks 6 times. Even when the
inverter P.C. board is normal, LED blinks 6 times after 3
minutes.

Is the bus-bar voltage of the inverter P.C. board normal?
(Refer to "TEST POINT DIAGRAM AND VOLTAGE" of the outdoor unit.)

Yes

Replace the indoor electronic control P.C. board.

[SUZ-KA71VA2.TH]

Содержание SUZ-KA25VA2











































































Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Похожие инструкции для SUZ-KA25VA2

Бренды по названию

Популярные бренды

Mitsubishi Electric SUZ-KA25VA2, Техническое и сервисное руководство

Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Похожие инструкции для SUZ-KA25VA2

Бренды по названию

Популярные бренды