Mitsubishi Electric SUZ-KA25VA2 страница 36 Скачать руководство пользователя

Страница: 36 / 74

G Check of R.V. coil

First of all, measure the resistance of R.V. coil to check if the coil is defective. Refer to 11-4.

In case CN721 is not connected or R.V. coil is open, voltage is generated between the terminal pins of the connector

although any signal is not being transmitted to R.V. coil.

Check if CN721 is connected.

Is there 230 VAC between CN721 and

on the inverter P.C. board 3 minutes

after the power supply is turned ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates COOL mode even if it is set to HEAT mode.

Is there 230 VAC between CN721 and

on the inverter P.C. board 3 minutes

after the power supply is turned ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates HEAT mode even if it is set to COOL mode.

Disconnect connector between

the compressor and the intelligent

power module.

Turn ON the power supply and

press EMERGENCY OPERATION

switch twice (HEAT mode).

Disconnect connector between

the compressor and the intelligent

power module.

Turn ON the power supply and

press EMERGENCY OPERATION

switch once (COOL mode).

[SUZ-KA25/35/50VA2.TH]

H Check of outdoor fan motor

Is the resistance between each ter-

minal of outdoor fan motor normal?

(Refer to 11-4.)

Check the connection between the

connector CN931 and CN932.

Disconnect CN932 from outdoor electronic control P.C. board or the inverter

P.C. board, and turn on the power supply.

Rotate the outdoor fan motor manually and measure the voltage of CN931.

Between 1(+) and 5(-)

Between 2(+) and 5(-)

Between 3(+) and 5(-)

Does the voltage between each terminal become 5 and 0

VDC repeatedly?

Does the outdoor fan motor rotate smoothly?

Replace the outdoor fan motor.

Replace the outdoor electronic control P.C. board or the inverter P.C. board.

Yes

(Fixed to either 5 or 0 VDC)

Yes

SUZ-KA50VA2.TH

SUZ-KA25/35VA2.TH

Is the resistance of outdoor fan motor

normal? (Refer to 11-4.)

Disconnect CN932 from the inverter

P.C. board, and measure the resist-

ance of the outdoor fan motor.

Replace the inverter P.C. board.

Replace the outdoor fan motor.

Yes

Содержание SUZ-KA25VA2











































































Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Похожие инструкции для SUZ-KA25VA2

Бренды по названию

Популярные бренды

Mitsubishi Electric SUZ-KA25VA2, Техническое и сервисное руководство

Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Похожие инструкции для SUZ-KA25VA2

Бренды по названию

Популярные бренды