Mitsubishi Electric SUZ-KA25VA2 Скачать руководство пользователя страница 24

Страница: 24 / 74

11-2-2. Wired remote controller

11-2-3. Failure mode table (Wireless remote controller/Wired remote controller)

Turn on the power.

Press the [CHECK] button twice.

Set refrigerant address with [TEMP] button

if system control is used.

Press the [ON/OFF] button to stop the self-check.

°C

SIMPLE

PAR-21MAA

ON/OFF

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

BACK

DAY

MONITOR/SET

CLOCK

ON/OFF

CHECK button

Refrigerant address

TEMP. button

IC: Indoor unit

OC: Outdoor unit

Check code

[Output pattern A] Errors detected by indoor unit

Beeper sounds/OPERATION INDICATOR

lamp blinks

Wireless remote controller

Check code

Wired remote controller

Symptom

Remark

(Number of times)

Intake sensor error

Pipe (TH2) sensor error
Pipe (TH5) sensor error

E6,E7

Indoor/outdoor unit communication error

Drain sensor error/Float switch connector open

Drain pump error

Freezing/Overheating protection operation

Communication error between indoor and outdoor units

Pipe temperature error

E4, E5

Remote controller signal receiving error

–

–
–

Indoor unit control system error (memory error, etc.)

–

E1, E2

Remote controller control board error

–

E0, E3

Remote controller transmission error

[Output pattern B] Errors detected by unit other than indoor unit (outdoor unit, etc.)

Check code

Symptom

Remark

Indoor/outdoor unit communication error (Transmitting error) (Outdoor unit)

Compressor overcurrent interruption

U3,U4

Open/short of outdoor unit thermistors

Compressor overcurrent interruption (When compressor locked)

Abnormal high discharging temperature/insufficient refrigerant

U1,Ud

Abnormal high pressure (63H worked)/Overheating protection operation

Abnormal temperature of heat sink

Outdoor unit fan protection stop

Compressor overcurrent interruption/Abnormal of power module

Abnormality of super heat due to low discharge temperature

U9,UH

Abnormality such as overvoltage or voltage shortage and abnormal
synchronous signal to main circuit/Current sensor error

12
13
14

Others

Other errors

• If the beeper does not sound again after the initial two beeps to confirm the self-check start signal was received and the OPERATION INDICATOR lamp

does not come on, there are no error records.

• If the beeper sounds three times continuously “beep, beep, beep (0.4 + 0.4 + 0.4 sec.)” after the initial two beeps to confirm the self-check start signal

was received, the specified refrigerant address is incorrect.

For details, check the LED display
of the outdoor controller board.

• On wireless remote controller

The continuous buzzer sounds from receiving section of indoor unit.
Blink of operation lamp

• On wired remote controller

Check code displayed in the LCD.

Beeper sounds/OPERATION INDICATOR

lamp blinks

Wireless remote controller

Wired remote controller

(Number of times)

Содержание SUZ-KA25VA2











































































Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric SUZ-KA25VA2, Техническое и сервисное руководство

Результаты поиска

Содержание SUZ-KA25VA2

Отзывы:

Бренды по названию

Популярные бренды