Mitsubishi Electric R16MTCPU Скачать руководство пользователя страница 61

Страница: 61 / 90

5 INSPECTION AND MAINTENANCE

5.1 Daily Inspection

INSPECTION AND MAINTENANCE

In order that you can use the Motion controller in normal and optimal condition, this section describes those items that must
be maintained or inspected daily or at regular intervals.

5.1

Daily Inspection

The items that must be inspected daily are shown below.

Item

Inspection item

Inspection

Criterion

Action

Installation modules

Check that the module is mounted
properly and the module fixing hook is
engaged securely.

The module must be mounted properly,
and module fixing hook must be engaged
securely.

Engage the module
fixing hook securely.

Motion CPU
module

READY LED

Check the READY LED is ON.

READY LED must be ON.



Page 34 LED

display

ERROR LED

Check the ERROR LED is OFF.

ERROR LED must be OFF.

Dot matrix LED

"RUN" is displayed.

"STP" is displayed.



" does not display.



Page 66 When an

error is displayed or
flickering in the dot
matrix LED



" does not display.

" AL" does not flicker.

Safety stops

Perform an emergency stop.

The main circuit power supply of the
servo amplifier is shut-off.



Page 54 Safety

circuit

Perform a servo amplifier forced stop.

AL.E6 (servo forced stop warning) occurs
at the servo amplifier.

Perform a Motion controller forced stop.

AL.E7 (controller forced stop warning)
occurs at the servo amplifier.

Содержание R16MTCPU



























































































Результаты поиска

Содержание R16MTCPU

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric R16MTCPU, Руководство пользователя

Результаты поиска

Содержание R16MTCPU

Отзывы:

Бренды по названию

Популярные бренды