Mitsubishi Electric R16MTCPU Скачать руководство пользователя страница 41

Страница: 41 / 90

2 EQUIPMENT SPECIFICATIONS

2.2 Motion CPU Module

Specifications

This section describes the Motion CPU specifications.

Module specifications

*1 Servo amplifiers for SSCNET cannot be used.
*2 SSCNET



and SSCNET



/H cannot be combined within the same line. For R64MTCPU/R32MTCPU, SSCNET



and SSCNET



can be set for each line.

*3 When using the optical hub unit, the maximum combined cable length depends on the system configuration.
*4 For half-duplex transmission, response time may be longer depending on the external device. When connecting with an external device

via a switching HUB, set to full-duplex transmission.

Item

R64MTCPU

R32MTCPU

R16MTCPU

Number of control axes

Up to 64 axes

Up to 32 axes

Up to 16 axes

SSCNET communication

Communication type

SSCNET



/H, SSCNET



Number of lines

2 lines

1 line

Distance between stations
(maximum) [m(ft.)]

SSCNET



100(328.08)

SSCNET



50(164.04)

Combined cable length
(maximum) [m(ft.)]

SSCNET



3200(10498.69)

1600(5249.34)

SSCNET



800(2624.67)

Number of sensing module connection
stations

Up to 8 stations (Up to 4 stations/line)

Up to 4 stations

Number of SSCNET



/H head module

connection stations

Number of optical hub unit connections

Up to 32 units (Up to 16 units/line)

Up to 16 units

PERIPHERAL I/F
(Ethernet)

Data transmission speed

100Mbps/10Mbps

Communication mode

Full-duplex/Half-duplex

Transmission method

Base band

Cable length (maximum) [m(ft.)]

30(98.43)

Memory card slot

SD/SDHC memory card compatible

Memory capacity

Standard ROM

12M bytes

SD memory card

Memory card capacity (Up to 32G bytes)

Number of stages of extension base

Up to 7 stages

Internal current consumption (5VDC) [A]

1.20

Mass [kg]

0.28

Exterior dimensions [mm(inch)]

106.0(4.17)(H)



27.8(1.09)(W)



110.0(4.33)(D)

Содержание R16MTCPU



























































































Результаты поиска

Содержание R16MTCPU

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric R16MTCPU, Руководство пользователя

Результаты поиска

Содержание R16MTCPU

Отзывы:

Бренды по названию

Популярные бренды