manualshive.com logo in svg

Mitsubishi Electric R16MTCPU, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric R16MTCPU Скачать руководство пользователя страница 49

2  EQUIPMENT SPECIFICATIONS

2.4  SSCNETIII Cables

47

2

Precautions for SSCNETIII cables

SSCNET

 cable is made from optical fiber. If optical fiber is added a power such as a major shock, lateral pressure, haul, 

sudden bending or twist, its inside distorts or breaks, and optical transmission will not be available. Especially, as optical fiber 
for MR-J3BUS

M and MR-J3BUS

M-A is made of synthetic resin, it melts down if being left near the fire or high 

temperature. Therefore, do not make it touched the part, which becomes high temperature, such as radiator or regenerative 
option of servo amplifier, or servo motor.
Be sure to use optical fiber within the range of operating temperature described in this manual.
Read described item of this section carefully and handle it with caution.

Minimum bend radius

Make sure to lay the cable with greater radius than the minimum bend radius. Do not press the cable to edges of equipment 
or others. For SSCNET

 cable, the appropriate length should be selected with due consideration for the dimensions and 

arrangement of Motion controller and servo amplifier. When closing the door of control panel, pay careful attention for 
avoiding the case that SSCNET

 cable is hold down by the door and the cable bend becomes smaller than the minimum 

bend radius.

Tension

If tension is added on the SSCNET

 cable, the increase of transmission loss occurs because of external force which 

concentrates on the fixing part of SSCNET

 cable or the connecting part of SSCNET

 connector. At worst, the breakage of 

SSCNET

 cable or damage of SSCNET

 connector may occur. For cable laying, handle without putting forced tension.

Lateral pressure

If lateral pressure is added on the SSCNET

 cable, the cable itself distorts, internal optical fiber gets stressed, and then 

transmission loss will increase. At worst, the breakage of SSCNET

 cable may occur. As the same condition also occurs at 

cable laying, do not tighten up SSCNET

 cable with a thing such as nylon band (TY-RAP).

Do not trample it down or tuck it down with the door of control panel or others.

Twisting

If SSCNET

 cable is twisted, it will become the same stress added condition as when local lateral pressure or bend is added. 

Consequently, transmission loss increases, and the breakage of SSCNET

 cable may occur at worst.

Disposal

When incinerating optical cable (cord) used for SSCNET

 cable, hydrogen fluoride gas or hydrogen chloride gas which is 

corrosive and harmful may be generated. For disposal of SSCNET

 cable, request for specialized industrial waste disposal 

services who has incineration facility for disposing hydrogen fluoride gas or hydrogen chloride gas.

Model name of SSCNETIII cable

Minimum bend radius[mm(inch)]

MR-J3BUS

M

25(0.98)

MR-J3BUS

M-A

Enforced covering cord : 50 (1.97)
Cord : 25 (0.98)

MR-J3BUS

M-B

Enforced covering cord : 50 (1.97)
Cord : 30 (1.18)

Model name of SSCNETIII cable

Maximum tension[N]

MR-J3BUS

M

=015

70

=03 to 3

140

MR-J3BUS

M-A

420 (enforced covering cord)

MR-J3BUS

M-B

980 (enforced covering cord)

Содержание R16MTCPU



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды