Mitsubishi Electric PUHZ-SP100YKA Скачать руководство пользователя страница 57

Страница: 57 / 108

OCH671

Main body

Lead wire

Stopper

Coil

Be sure to attach

the stopper.

(3) How to attach and detach the coil of linear expansion valve

Linear expansion valve is separable into the main body and the coil as shown in the diagram below.

<How to detach the coil>

Hold the lower part of the main body (shown as A) firmly so that

the main body does not move and detach the coil by pulling it

upward.

Be sure to detach the coil holding main body firmly. Otherwise

pipes can bend due to stress.

<How to attach the coil>

Hold the lower part of the main body (shown as A) firmly so that

the main body does not move and attach the coil by inserting it

downward into the main body. Then securely attach the coil stop-

per to main body. (At this time, be careful that stress is not added

to lead wire and main body is not wound by lead wire.) If the

stopper is not firmly attached to main body, coil may be detached

from the main body and that can cause defective operation of lin-

ear expansion valve.

To prevent piping stress, be sure to attach the coil holding the

main body of linear expansion valve firmly. Otherwise pipe may

break.

Содержание PUHZ-SP100YKA













































































































Результаты поиска

Содержание PUHZ-SP100YKA

Отзывы:

Похожие инструкции для PUHZ-SP100YKA

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHZ-SP100YKA, Руководство по обслуживанию

Результаты поиска

Содержание PUHZ-SP100YKA

Отзывы:

Похожие инструкции для PUHZ-SP100YKA

Бренды по названию

Популярные бренды