Mitsubishi Electric PUHZ-SP100YKA Скачать руководство пользователя страница 108

Страница: 108 / 108

108

13. Removing the compressor (MC)

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove 2 front cover panel fixing screws (5 × 12) and

remove the front cover panel. (See Photo 1)

(4) Remove 3 valve bed fixing screws (5 × 12) and 4 stop valve

fixing screws (5 × 16, 2 for gas and 2 for liquid) and then

remove the valve bed.

(5) Remove the nut from the terminal cover. (See Photo 17)

(6) Remove the terminal cover to disconnect the compressor

lead wire.

(7) Recover refrigerant.

(8) Remove the 3 points of the compressor fixing nut using a

spanner or an adjustable wrench.

(9) Remove the welded pipe of compressor inlet and outlet

and then remove the compressor.

Note: Recover refrigerant without spreading it in the air.

Compressor

(MC)

Compressor

fixing nuts

Compressor

lead wire

Terminal

cover

OPERATING PROCEDURE

PHOTOS/FIGURES

11. Removing the 4-way valve coil (21S4)

(1) Remove the service panel. (See Photo 1)

[Removing the 4-way valve coil]

(2) Remove 4-way valve coil fixing screw (M5 × 6.5).

(3) Remove the 4-way valve coil by sliding the coil toward you.

(4) Disconnect the connector 21S4 (green) on the outdoor

multi controller circuit board in the electrical parts box.

12. Removing the 4-way valve

(1) Remove the service panel. (See Photo 1)

(2) Remove the top panel. (See Photo 1)

(3) Remove the electrical parts box (See Photo 4)

(4) Remove 3 valve bed fixing screws (5 × 12) and 8 stop valve

fixing screws (5 × 16) and then remove the valve bed. (See

Photo 18)

(5) Remove 4 right side panel fixing screw (5 × 12) in the rear

of the unit and then remove the right side panel.

(6) Remove the 4-way valve coil. (See Photo 19)

(7) Recover refrigerant.

(8) Remove the welded part of 4-way valve.

Note 1: Recover refrigerant without spreading it in the air.

Note 2: The welded part can be removed easily by remov-

ing the right side panel.

Note 3: When installing the 4-way valve, cover it with a

wet cloth to prevent it from heating (120°C or more),

then braze the pipes so that the inside of pipes

are not oxidized.

Photo 20

HEAD OFFICE : TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Specifications are subject to change without notice.

Published: Sep. 2017 No.OCH671

Made in Japan

Содержание PUHZ-SP100YKA













































































































Результаты поиска

Содержание PUHZ-SP100YKA

Отзывы:

Похожие инструкции для PUHZ-SP100YKA

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHZ-SP100YKA, Руководство по обслуживанию

Результаты поиска

Содержание PUHZ-SP100YKA

Отзывы:

Похожие инструкции для PUHZ-SP100YKA

Бренды по названию

Популярные бренды