Mitsubishi Electric PUHZ-SP100YKA Скачать руководство пользователя страница 40

Страница: 40 / 108

OCH671

Check code

Abnormal points and detection method

Judgment and action

Case

(6607

6608)

Non defined check code

This code is displayed when non defined

check code is received.

Noise has entered transmission

wire of remote controller.

Noise has entered indoor/ out-

door unit connecting wire.

Outdoor unit is not a series of

power-inverter.

Turn the power off, and on again to check.

Replace indoor controller board or outdoor

controller circuit board if abnormality is

displayed again.

Replace outdoor unit with power-inverter type

outdoor unit.

(0403)

Serial communication error

Abnormal if serial communication

between outdoor controller circuit board

and outdoor power circuit board is defec-

tive.

Breaking of wire or contact

failure of connector CN2

between the outdoor controller

circuit board and the outdoor

power circuit board

Breaking of wire or contact

failure of connector CN4

between the outdoor controller

circuit board and the outdoor

power circuit board

Defective communication circuit

of outdoor power circuit board

Defective communication circuit

of outdoor controller circuit board

for outdoor power circuit board

Check connection of each connector CN2

and CN4 between the outdoor controller

circuit board and the outdoor power circuit

board.

Replace outdoor power circuit board.

Replace outdoor controller circuit board.

Breaking of wire or contact

failure of connector between

outdoor controller circuit board

and M-NET board

Contact failure of M-NET board

power supply line

Noise has entered into M-NET

transmission wire.

Abnormal if communication between

outdoor controller circuit board and

M-NET board is not available.

Check disconnection, looseness, or breaking of

connection wire between outdoor controller cir-

cuit board (CNMNT) and M-NET board (CN5).

Check disconnection, looseness, or breaking of

connection wire between outdoor controller cir-

cuit board (CNMNT) and M-NET board (CND).

Check M-NET transmission wiring method.

Slight temperature difference

between indoor room

temperature and pipe <liquid

or condenser/evaporator>

temperature thermistor

• Shortage of refrigerant

• Disconnected holder of

pipe <liquid or condenser/

evaporator> thermistor

• Defective refrigerant circuit

Converse connection of

extension pipe (on plural units

connection)

Converse wiring of indoor/

outdoor unit connecting wire

(on plural units connection)

Defective detection of indoor

room temperature and pipe

temperature thermistor

Stop valve is not opened

completely.

Pipe temperature

Detected as abnormal when the pipe

temperature is not in the cooling range

3 minutes after compressor start and

6 minutes after the liquid or condenser/

evaporator pipe is out of cooling range.

Note 1) It takes at least 9 minutes to detect.

Note 2) Abnormality P8 is not detected in

drying mode.

Cooling range : Indoor pipe temperature

(TH2 or TH5) − intake temperature

(TH1)

[

−3

°C

TH: Lower temperature between liquid pipe

temperature and condenser/evaporator

temperature

–

Check pipe <liquid or condenser/

evaporator> temperature with room

temperature display on remote controller

and outdoor controller circuit board.

Pipe <liquid or condenser / evaporator>

temperature display is indicated by setting

SW2 of outdoor controller circuit board as

follows.

Check converse connection of extension

pipe or converse wiring of indoor/outdoor

unit connecting wire.

Conduct temperature check with outdoor

controller circuit board after connecting

‘A-Control Service Tool (PAC-SK52ST)’.

(

)

OFF

A-Control Service Tool SW2 setting

Temperature display of indoor liquid pipe

Indoor 1

Temperature display of indoor liquid pipe

Indoor 2

Temperature display of indoor condenser/

evaporator pipe Indoor 1

Temperature display of indoor condenser/

evaporator pipe Indoor 2

(6841)

Indoor/outdoor unit communication

error (Transmitting error) (Outdoor unit)

Abnormal if “0” receiving is detected 30

times continuously though outdoor con-

troller circuit board has transmitted “1”.

Abnormal if outdoor controller circuit

board could not find blank of transmission

path for 3 minutes.

Indoor/ outdoor unit connecting

wire has contact failure.

Defective communication circuit

of outdoor controller circuit board

Noise has entered power supply.

Noise has entered indoor/ out-

door unit connecting wire.

Check disconnection or looseness of indoor/

outdoor unit connecting wire.

–

Turn the power off, and on again to

check. Replace outdoor controller circuit

board if abnormality is displayed again.

Содержание PUHZ-SP100YKA













































































































Результаты поиска

Содержание PUHZ-SP100YKA

Отзывы:

Похожие инструкции для PUHZ-SP100YKA

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHZ-SP100YKA, Руководство по обслуживанию

Результаты поиска

Содержание PUHZ-SP100YKA

Отзывы:

Похожие инструкции для PUHZ-SP100YKA

Бренды по названию

Популярные бренды