Mitsubishi Electric PLFY-WP VBM-E, Руководство по установке

Страница: 10 / 30

GB
Electrical Z or N
9 Ho Z to set the ¿[ ed up do Z n air direction (Onl \
I or Z ired re P ote controller)
Ŷ
E [ planation o I Z ord
Address No. of indoor unit is the number given to each air conditioner.
Outlet No. is the number given to each outlet of air conditioner.
(Refer to the right.)
Up Down air direction is the direction (angle) to x.
For PLFY-BM, only the particular outlet can be fixed to certain direction with
the procedures below. Once fixed, only the set outlet is fixed every time air
conditioner is turned on. (Other outlets follow UP DOWN air direction setting of
the remote controller.)
8 Electrical characteristics
Symbols: MCA: Max. Circuit Amps ( 1.25×FLA) FLA: Full Load Amps
IFM: Indoor Fan Motor Output: Fan motor rated output
Model
Power supply IFM
olts Hz Range - 1 MCA (A) Output (kW) FLA (A)
PLFY-WP32 BM-E
22 -24 5 Hz
Max.: 264
Min.: 19
.44 . 5 .35
PLFY-WP4 BM-E .44 . 5 .35
PLFY-WP5 BM-E .57 . 5 .45
Ŷ
Manual Y ane angle
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Maintenance
Initial setting
Service
F1 F2 F3 F4
Maintenance menu
Main menu:
Cursor
Auto descending panel
Manual vane angle
F1 F2 F3 F4
Manual vane angle
Input display:
Cur. Address Check
M-NET address
Identify unit Check button
1
Select Maintenance from the Main
menu, and press the [SELECT]
button.
2 Select Manual vane angle with the
[F1] or [F2] button, and press the
[SELECT] button.
3
Select the M-NET address for the
units to whose vanes are to be xed,
with the [F2] or [F3] button, and press
the [SELECT] button.
Press the [F4] button to con rm the
unit.
The vane of only the target indoor
unit is pointing downward.
Ŷ
Con ¿ r P ation procedure
F1 F2 F3 F4
Manual vane angle
Input display:
Cur. Address Check
M-NET address
Identify unit Check button
F1 F2 F3 F4
Manual vane angle
Input display:
M-NET address
The air conditioner with the
vane pointing downward is
the target air conditioner.
F1 F2 F3 F4
Manual vane angle
Input display:
There is no response from
the target device.
Confirm the state of the air
conditioner.
1
Select the M-NET address for the
units to whose vanes are to be xed,
with the [F2] or [F3]
button.
Press the [F4] button to con rm
the unit.
2 After pressing the [F4] button, wait
approximately 15 seconds, and
then check the current state of the
air conditioner.
The vane is pointing downward.
This air conditioner is displayed
on the remote controller.
All outlets are closed. Press
the [RETURN] button and continue
the operation from the beginning.
The messages shown to the left
are displayed. The target device
does not exist at this refrigerant ad-
dress.
Press the [RETURN] button to
return to the initial screen.
3
Change the M-NET address to
the next number.
Refer to step 1 to change the M-
NET address and continue with the
con rmation.
Outlet No.3
Downward
Horizontal air ow
* When it is cold because of direct air ow,
the air ow direction can be xed horizon-
tally to avoid direct air ow.
Fixed setting
The air ow direction of this
outlet is xed in particular
direction.
Remote controller setting
The air ow direction of this outlet
is controlled by the air ow direc-
tion setting of remote controller.
Outlet No.4
Outlet No.2
Note: “ ” indicates all outlets.
Outlet No.1
MITSUBISHI
ELECTRIC
label