Mitsubishi Electric MUZ-FH25VE Скачать руководство пользователя страница 49

Страница: 49 / 54

OPERATING PROCEDURE

PHOTOS

5. Removing outdoor fan motor

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Disconnect the following connectors:

CN931, CN932 (Fan motor)

(3) Remove the propeller nut.
(4) Remove the propeller.
(5) Remove the screws fixing the fan motor.
(6) Remove the fan motor.

Photo 6

Photo 7

6. Removing the compressor and 4-way valve

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Remove the inverter assembly. (Refer to 2.)
(3) Recover gas from the refrigerant circuit.

NOTE:

Recover gas from the pipes until the pressure gauge

shows 0 kg/cm

(0 MPa).

(4) Detach the brazed part of the suction and the discharge pipe

connected with compressor.

(5) Remove the nuts of compressor legs.
(6) Remove the compressor.
(7) Detach the brazed part of pipes connected with 4-way valve.

Propeller nut

Screws of the outdoor fan motor

Propeller

Photo 8

Defrost thermistor

Outdoor heat
exchanger tempera-
ture thermistor

Brazed parts of 4-way valve

Suction pipe
brazed part

Discharge pipe
brazed part

OBH624A

Содержание MUZ-FH25VE























































Результаты поиска

Содержание MUZ-FH25VE

Отзывы:

Похожие инструкции для MUZ-FH25VE

Бренды по названию

Популярные бренды

Mitsubishi Electric MUZ-FH25VE, Руководство по обслуживанию

Результаты поиска

Содержание MUZ-FH25VE

Отзывы:

Похожие инструкции для MUZ-FH25VE

Бренды по названию

Популярные бренды