Mitsubishi Electric MUZ-FH25VE Скачать руководство пользователя страница 36

Страница: 36 / 54

H Check of R.V. coil

First of all, measure the resistance of R.V. coil to check if the coil is defective. Refer to 11-4.

In case CN721 is disconnected or R.V. coil is open, voltage is generated between the terminal pins of the connector

although no signal is being transmitted to R.V. coil.

Check if CN721 is connected.

Is there 230 VAC between CN721 and

on the inverter P.C. board 3 minutes

after the power supply is turned ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates COOL mode even if it is set to HEAT mode.

Is there 230 VAC between CN721 and

on the inverter P.C. board 3 minutes

after the power supply is turned ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates HEAT mode even if it is set to COOL mode.

Disconnect connector between the

compressor and the power module

(IC700).

Turn ON the power supply and press

EMERGENCY OPERATION switch

twice (HEAT mode).

Disconnect connector between the

compressor and the power module

(IC700).

Turn ON the power supply and

press EMERGENCY OPERATION

switch once (COOL mode).

First of all, measure the resistance of R.V. coil to check if the coil is defective. Refer to 11-4.

In case CN602 is disconnected or R.V. coil is open, voltage is generated between the terminal pins of the connector

although no signal is being transmitted to R.V. coil.

Check if CN602 is connected.

Is there 230 VAC between CN602 and

on the inverter P.C. board 3 minutes

after the power supply is turned ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates COOL mode even if it is set to HEAT mode.

Is there 230 VAC between CN602 and

on the inverter P.C. board 3 minutes

after the power supply is turned ON?

Yes

Replace the inverter

P.C. board.

Replace the 4-way valve.

Unit operates HEAT mode even if it is set to COOL mode.

Disconnect connector between the

compressor and the IGBT module

(IC700).

Turn ON the power supply and press

EMERGENCY OPERATION switch

twice (HEAT mode).

Disconnect connector between the

compressor and the IGBT module

(IC700).

Turn ON the power supply and

press EMERGENCY OPERATION

switch once (COOL mode).

MUZ-FH25/35

MUZ-FH50

OBH624A

Содержание MUZ-FH25VE























































Результаты поиска

Содержание MUZ-FH25VE

Отзывы:

Похожие инструкции для MUZ-FH25VE

Бренды по названию

Популярные бренды

Mitsubishi Electric MUZ-FH25VE, Руководство по обслуживанию

Результаты поиска

Содержание MUZ-FH25VE

Отзывы:

Похожие инструкции для MUZ-FH25VE

Бренды по названию

Популярные бренды