background image

JG79J514H25

Required Tools for Installation

Phillips screwdriver
Level
Scale
Utility knife or scissors
65 mm hole saw
Torque wrench
Wrench (or spanner)

4 mm hexagonal wrench
Flare tool for R32, R410A
Gauge manifold for R32, R410A
Vacuum pump for R32, R410A
Charge hose for R32, R410A
Pipe cutter with reamer

ENGLISH

REFRIGERANT

SPLIT-TYPE AIR CONDITIONERS

INSTALLATION MANUAL

Model names are indicated in 1-3.

When installing multi units, refer to the 
installation manual of the multi unit for 
outdoor unit installation.

English is 

original.

1.  BEFORE INSTALLATION

MEANINGS OF SYMBOLS DISPLAYED ON INDOOR UNIT AND/OR OUTDOOR UNIT

WARNING

5LVNRI¿UH

7KLVXQLWXVHVDÀDPPDEOHUHIULJHUDQW
,IUHIULJHUDQWOHDNVDQGFRPHVLQFRQWDFWZLWK¿UHRUKHDWLQJSDUWLWZLOOFUHDWHKDUPIXOJDVDQGWKHUHLVULVNRI¿UH

Read the OPERATING INSTRUCTIONS carefully before operation.

Service personnel are required to carefully read the OPERATING INSTRUCTIONS and INSTALLATION MANUAL before operation.

Further information is available in the OPERATING INSTRUCTIONS, INSTALLATION MANUAL, and the like.

1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY

•  Be sure to read “THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY” before installing the air conditioner.
•  Before starting the connection setup of the Wi-Fi interface, check the safety precautions in OPERATING INSTRUCTIONS of the ro

om air conditioner.

‡ %HVXUHWRREVHUYHWKHZDUQLQJVDQGFDXWLRQVVSHFL¿HGKHUHDVWKH\LQFOXGHLPSRUWDQWLWHPVUHODWHGWRVDIHW\

•  After reading this manual, be sure to keep it together with the OPERATING INSTRUCTIONS for future reference.

 WARNING

(Could lead to death, serious injury, etc.)

  Do not install the unit by yourself (user).

 ,QFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHHOHFWULFVKRFN

injury due to the unit falling, or leakage of water. Con-

sult the dealer from whom you purchased the unit or a 

TXDOL¿HGLQVWDOOHU

 Perform the installation securely referring to the 

installation manual.

 ,QFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHHOHFWULFVKRFN

injury due to the unit falling, or leakage of water. 

  When installing the unit, use appropriate protective 

equipment and tools for safety.

 

Failure to do so could cause injury.

  Install the unit securely in a place which can bear 

the weight of the unit.

 

If the installation location cannot bear the weight of the 
unit, the unit could fall causing injury.

  Do not alter the unit.

 ,WPD\FDXVH¿UHHOHFWULFVKRFNLQMXU\RUZDWHUOHDNDJH

■ 

(OHFWULFDOZRUNVKRXOGEHSHUIRUPHGE\DTXDOL¿HG

experienced electrician, according to the installation 
manual. Be sure to use an exclusive circuit. Do not 
connect other electrical appliances to the circuit.

 ,IWKHFDSDFLW\RIWKHSRZHUFLUFXLWLVLQVXI¿FLHQWRUWKHUH

LVLQFRPSOHWHHOHFWULFDOZRUNLWFRXOGUHVXOWLQD¿UHRU

an electric shock.

  Earth the unit correctly.

  Do  not  connect  the  earth  to  a  gas  pipe,  water  pipe, 

lightning  rod,  or  telephone  earth.  Defective  earthing 

could cause electric shock.

■ 

Do not damage the wires by applying excessive 
pressure with parts or screws.

 'DPDJHGZLUHVFRXOGFDXVH¿UHRUHOHFWULFVKRFN

■ 

Be sure to cut off the main power in case of setting 
up the indoor P.C. board or wiring works.

 

Failure to do so could cause electric shock.

 8VHWKHVSHFL¿HGZLUHVWRFRQQHFWWKHLQGRRUDQG

RXWGRRUXQLWVVHFXUHO\DQGDWWDFKWKHZLUHV¿UPO\WR

the terminal block connecting sections so the stress 
of the wires is not applied to the sections. Do not 
extend the wires, or use intermediate connection.

 ,QFRPSOHWHFRQQHFWLQJDQGVHFXULQJFRXOGFDXVH¿UH

■ 

'RQRWLQVWDOOWKHXQLWLQDSODFHZKHUHÀDPPDEOH

gas may leak.

  If gas leaks and accumulates in the area around the 

unit, it could cause an explosion.

 Do not use intermediate connection of the power 

cord or the extension cord and do not connect many 
devices to one AC outlet.

 ,WFRXOGFDXVHD¿UHRUDQHOHFWULFVKRFNGXHWRGHIHFWLYH

contact, defective insulation, exceeding the permissible 
current, etc.

■ 

%HVXUHWRXVHWKHSDUWVSURYLGHGRUVSHFL¿HGSDUWV

for the installation work.

  The use of defective parts could cause an injury or 

OHDNDJHRIZDWHUGXHWRD¿UHDQHOHFWULFVKRFNWKH

unit falling, etc.

■ 

When plugging the power supply plug into the 
outlet, make sure that there is no dust, clogging, 
or loose parts in both the outlet and the plug. Make 
sure that the power supply plug is pushed com-
pletely into the outlet.

  If there is dust, clogging, or loose parts on the power 

supply plug or the outlet, it could cause electric shock or 

¿UH,IORRVHSDUWVDUHIRXQGRQWKHSRZHUVXSSO\SOXJ

replace it.

■ 

Attach the electrical cover to the indoor unit and the 
service panel to the outdoor unit securely.

 

If the electrical cover of the indoor unit and/or the service 
panel of the outdoor unit are not attached securely, it 

FRXOGUHVXOWLQD¿UHRUDQHOHFWULFVKRFNGXHWRGXVW

water, etc.

■ 

When installing, relocating, or servicing the unit, 
make sure that no substance other than the speci-

¿HGUHIULJHUDQW5HQWHUVWKHUHIULJHUDQWFLUFXLW

  Any presence of foreign substance such as air can 

cause abnormal pressure rise and may result in explo-

sion or injury. The use of any refrigerant other than that 

VSHFL¿HGIRUWKHV\VWHPZLOOFDXVHPHFKDQLFDOIDLOXUH

system malfunction, or unit breakdown. In the worst 
case, this could lead to a serious impediment to securing 
product safety.

■ 

Do not discharge the refrigerant into the atmos-
phere. If refrigerant leaks during installation, ven-
tilate the room. Check that the refrigerant does not 
leak after installation has been completed.

 ,I UHIULJHUDQW OHDNV DQG FRPHV LQ FRQWDFW ZLWK ¿UH RU

heating part of such a fan heater, kerosene heater, or 

cooking stove, it will create harmful gas. Provide ventila-

tion in accordance with EN378-1.

■ 

Use appropriate tools and piping materials for instal-
lation.

  The pressure of R32 is 1.6 times more than R22. Not 

using appropriate tools or materials and incomplete 
installation could cause the pipes to burst or injury. 

■ 

When pumping down the refrigerant, stop the com-
pressor before disconnecting the refrigerant pipes.

  If the refrigerant pipes are disconnected while the 

compressor is running and the stop valve is open, air 
could be drawn in and the pressure in the refrigeration 
cycle could become abnormally high. This could cause 
the pipes to burst or injury.

■ 

When installing the unit, securely connect the re-
frigerant pipes before starting the compressor.

 

If the compressor is started before the refrigerant pipes 
are connected and when the stop valve is open, air could 
be drawn in and the pressure in the refrigeration cycle 
could become abnormally high. This could cause the 
pipes to burst or injury.

■ 

)DVWHQDÀDUHQXWZLWKDWRUTXHZUHQFKDVVSHFL¿HG

in this manual.

 ,IIDVWHQHGWRRWLJKWDÀDUHQXWPD\EUHDNDIWHUDORQJ

period and cause refrigerant leakage.

■ 

The unit shall be installed in accordance with na-
tional wiring regulations.

■ 

:KHQXVLQJDJDVEXUQHURURWKHUÀDPHSURGXFLQJ

equipment, completely remove all of the refrigerant 
from the air conditioner and ensure that the area is 
well-ventilated.

 ,IWKHUHIULJHUDQWOHDNVDQGFRPHVLQFRQWDFWLQ¿UHRU

heating part, it will create harmful gas and there is risk 

RI¿UH

■ 

Do not use means to accelerate the defrosting pro-
cess or to clean, other than those recommended by 
the manufacturer.

■ 

The appliance shall be stored in a room without 
continuously operating ignition sources (for exam-

SOHRSHQÀDPHVDQRSHUDWLQJJDVDSSOLDQFHRUDQ

operating electric heater).

■ 

Do not pierce or burn.

■ 

Be aware that refrigerants may not contain an odour.

■ 

Pipe-work shall be protected from physical damage.

■ 

The installation of pipe-work shall be kept to a 
minimum.

■ 

Compliance with national gas regulations shall be 
observed.

■ 

Keep any required ventilation openings clear of 
obstruction.

  Do not install the indoor unit equipped with the Wi-Fi 

interface nearby the automatic control devices such 

DVDXWRPDWLFGRRUVRU¿UHDODUPV

 

It can cause accidents due to malfunctions.

  Do not use the indoor unit equipped with the Wi-Fi 

interface nearby the medical electrical equipment 
or people who have a medical device such as a 
cardiac pacemaker or an implantable cardioverter-

GH¿EULOODWRU

  It can cause an accident due to malfunctions of the 

medical equipment or device.

  This indoor unit equipped with the Wi-Fi interface 

should be installed and operated with a minimum 
distance of 20 cm between the device and the user 
or bystanders.

Содержание MSZ-LN18VG2









Отзывы: