background image

5-3. PUMPING DOWN

When relocating or disposing of the air conditioner, pump down the system following
the procedure below so that refrigerant is not released into the atmosphere.
1) Connect the gauge manifold valve to the service port of the stop valve on the gas

pipe side of the outdoor unit.

2) Fully close the stop valve on the liquid pipe side of the outdoor unit.
3) Close the stop valve on the gas pipe side of the outdoor unit almost completely

so that it can be easily closed fully when the pressure gauge shows 0 MPa [Gauge]
(0 lbf/in.

2

[0 kgf/cm

2

]).

4) Start the emergency COOL operation.
 To start the emergency operation in COOL mode, disconnect the power supply

plug and/or turn off the breaker. After 15 seconds, connect the power supply plug
and/or turn on the breaker, and then press the E.O. SW once. (The emergency
COOL operation can be performed continuously for up to 30 minutes.)

5) Fully close the stop valve on the gas pipe side of the outdoor unit when the pressure

gauge shows 0.05 to 0 MPa [Gauge] (approx. 7.25 to 0 lbf/in

2

[0.5 to 0 kgf/cm

2

]).

6) Stop the emergency COOL operation.
 Press the E.O. SW twice to stop the operation.

5. RELOCATION AND MAINTENANCE

HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO
100-8310, JAPAN

5-1. REMOVING AND INSTALLING THE PANEL  

 

ASSEMBLY

Removal procedure

1) Remove the two screws that attach the panel assembly.

5HPRYHWKHSDQHODVVHPEO\%HVXUHWRUHPRYHLWVERWWRPHQG¿UVW

5-2. REMOVING THE INDOOR UNIT

Remove the bottom of the indoor unit from the installation plate.
When releasing the corner part, release both left and right bottom corner part of

LQGRRUXQLWDQGSXOOLWGRZQZDUGDQGIRUZDUGDVVKRZQLQWKH¿JXUHRQWKHULJKW

Push

Lower

Square hole

Installation procedure

1) Install the panel assembly following the removal procedure in reverse.
2) Be sure to press the positions as indicated by the arrows in order to attach the

assembly completely to the unit.

If the above method cannot be used

Remove the front panel. Then, insert hexagonal wrenches into the square holes on

WKHOHIWDQGULJKWVLGHVRIWKHXQLWDQGSXVKWKHPXSDVVKRZQLQWKHIROORZLQJ¿JXUH

The bottom of the indoor unit lowers and releases the hooks.

Содержание Mr. Slim MSZ-FD09NA









Отзывы: