Mitsubishi Electric MELSEC FX2N-64CL-M Скачать руководство пользователя страница 64

Страница: 64 / 74

FX2N-64CL-M CC-Link/LT Master Block

Troubleshooting 12

12-2

12.2

Confirmation of status based on status indicator LEDs and countermeasures

12.2.1

ONLINE mode

The table below shows the descriptions of errors during in the ONLINE mode (bits 6 and 7 of
the DIP switches are OFF in the FX

-64CL-M), indicated by the status indicator LEDs and

their countermeasures.

Name

Description

Countermeasures

tus

indic

tor

POWER

Lit: Power is supplied
Extinguished: Power is not
supplied

Extinguished
• Confirm the capacity of the power for the PLC and

the supplied 5V DC power.

RUN

Lit: FX

-64CL-M is operating

normally

Extinguished: FX

-64CL-M is

abnormal
Power is interrupted
EEPROM read
error (sum
mismatch) occurred

Extinguished
• Confirm the capacity of the power for the PLC and

the supplied 5 VDC power.

• Set the FX

-64CL-M to the CONFIG mode. If

necessary, edit the detailed remote station
information, and write it to the EEPROM.

• If the system is not restored even after confirming

the items above, contact an office of MITSUBISHI
ELECTRIC SYSTEM & SERVICE, CO., LTD.

ERR.

Lit: Communication speed setting

error occurred
EEPROM read error (sum
mismatch) occurred

Flickering: Power supplied for

communication is
abnormal
DIP switch for
operation setting was
changed during
operation

Extinguished: FX

-64CL-M is

operating normally

Lit
• Confirm the DIP switch setting, reset power.
• Set the FX

-64CL-M to the CONFIG mode. If

necessary, edit the detailed remote station
information, and write it to the EEPROM.

Flickering
• Return the DIP switch setting to the status at the

time of power ON.

• If the DIP switch setting should be changed,

change the DIP switch setting, then execute the
CONFIG mode again.

• Confirm connection to the power adapter and the

power supplied to the power adapter. (For the
details of power adapter, refer to the User's Manual
(Detailed Volume) of the power adapter.)

L RUN

Lit: Data link is being executed
Extinguished: Data link is stopped

Extinguished
• Take proper countermeasures according to the

status of other LEDs.

L ERR.

Lit: Use station number

discrepancy
(when BFM#32(20h) to
#95(5Fh) is edited, the station
numbers are checked.)
Outside-control-range station
error occurred

Flickering: Stations are abnormal
Extinguished: Data link is being

executed normally

Lit
• Securely connect the FX

-64CL-M and remote I/O

units.

• Make sure that connected remote I/O units are

consistent with the detailed remote station
information.

Flickering
• Securely connect the FX

-64CL-M and remote I/O

units.

• Make sure that connected remote I/O units are

consistent with the detailed remote station
information.

Содержание MELSEC FX2N-64CL-M











































































Результаты поиска

Содержание MELSEC FX2N-64CL-M

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric MELSEC FX2N-64CL-M, Руководство пользователя

Результаты поиска

Содержание MELSEC FX2N-64CL-M

Отзывы:

Бренды по названию

Популярные бренды