Mitsubishi Electric MELSEC FX2N-64CL-M Скачать руководство пользователя страница 30

Страница: 30 / 74

FX2N-64CL-M CC-Link/LT Master Block

Connection of Cables, Connectors and Terminating Resistors 6

6-2

6.1

Connection of units using flat cables dedicated to CC-Link/LT

This paragraph explains the connection method using flat cables dedicated to CC-Link/LT.

1) The connection order of dedicated flat cables has no relevance to the station No.

2) Lay out the FX

-64CL-M at either end of the trunk line.

Connect a terminating resistor on the FX

-64CL-M side in a position that is within 20 cm

from the FX

-64CL-M.

3) Make sure to connect a terminating resistor to each end of the trunk line the CC-Link/LT.

Connect T-branches and remote I/O units using the connectors for dedicated flat cable.

6.2

How to attach connectors used for dedicated flat cable

This paragraph explains how to attach connectors used for the dedicated flat cable.

1) Components

The components are as shown below.

T-branch area

Master station/remote station/power adapter connection area

Trunk line

Drop line

Connector for dedicated
flat cable

Connector for
dedicated
flat cable

Connector for dedicated
flat cable

-Master station (FX

-64CL-M)

-Power adapter (CL1PAD1)
-Terminal block type remote
I/O unit
-Sensor connector type remote
I/O unit
-MIL collector type remote I/O unit

Connector for
dedicated
flat cable

Cable type
remote I/O unit

Connector for dedicated
flat cable

C o m p o n e n t 1 : C o v e r

C o m p o n e n t 2 : B o d y

C o m p o n e n t 3 : D e d i c a t e d f l a t

c a b l e

O r a n g e c o l o r

Содержание MELSEC FX2N-64CL-M











































































Результаты поиска

Содержание MELSEC FX2N-64CL-M

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric MELSEC FX2N-64CL-M, Руководство пользователя

Результаты поиска

Содержание MELSEC FX2N-64CL-M

Отзывы:

Бренды по названию

Популярные бренды