manualshive.com logo in svg

Mitsubishi Electric MELSEC FX2N-64CL-M, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC FX2N-64CL-M Скачать руководство пользователя страница 24

FX2N-64CL-M CC-Link/LT Master Block

System Configuration 4

4-2

4.1

Total configuration

This paragraph describes the system configuration and cautions for CC-Link/LT.

•

Connect the master station, power adapter and remote stations using the flat cables
dedicated to CC-Link/LT and the connectors for dedicated flat cables.

•

The connection order of remote stations has no relevance to the station No.
Even if the station No. of remote stations is not consecutive, no error will occur in the data
link.

•

In the CC-Link/LT system, terminating resistors should be connected to both ends of the
trunk line.
Connect the terminating resistor on the FX

2N

-64CL-M side to a position within 200 mm

(7.87") from the FX

2N

-64CL-M.

•

Make sure to lay out the master block on one side of the trunk line.

•

Up to 64 remote stations can be connected to one FX

2N

-64CL-M as far as the condition

shown in the table below are satisfied.

•

Equipment for CC-Link cannot be connected to the CC-Link/LT system.
On the contrary, equipment for CC-Link/LT cannot be connected to the CC-Link system.

•

Refer to the respective instruction manuals when installing the power adapter or remote I/O
units.

•

Refer to the homepage of the CC-Link Partner Association (CLPA) "http://www.cc-link.org/"
for details concerning flat cabling, terminating resistors and connector for CC-Link/LT.

Item

Specification

Remarks

Communication speed

2.5Mbps

625kbps

156kbps

--

Distance between 
stations

No restriction

--

Maximum number of 
modules connected in 1 
drop line

8 units

Maximum number of 

remote I/O units connected 

per branch in a drop line

Maximum trunk length

35m (114' 9") 100m (328' 1") 500m (1640' 5")

Cable length between 

terminating resistors

(excluding drop line length)

T-branch interval

No restriction

--

Maximum drop length

4m (13' 1")

16m (52' 5")

60m (196' 10")

Cable length per branch

Cumulative drop line 
length

15m (49' 2")

50m (164' 0")

200m (656' 2")

Sum of all drop lines

PLC main unit

Terminating

resistor

T branch
connection

T-branch interval

Power

adapter

Remote

I/O station

Remote

I/O station

Drop length

(including branch)

Remote

I/O station

Remote

I/O station

Remote

I/O station

Remote

I/O station

Distance between

stations

Terminating

resistor

Trunk length (branch line length not included)

Trunk line

Drop line

Содержание MELSEC FX2N-64CL-M











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды