manualshive.com logo in svg

Mitsubishi Electric MELSEC FX2N-64CL-M, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC FX2N-64CL-M Скачать руководство пользователя страница 25

FX2N-64CL-M CC-Link/LT Master Block

System Configuration 4

4-3

4.2

PLC connection

This paragraph explains which PLC series are connectable with the FX

2N

-64CL-M and

cautions on the number of connectable FX

2N

-64CL-M.

4.2.1

Applicable PLC and number of connectable FX

2N

-64CL-M

•

Connect the FX

2N

-64CL-M to the right side of the PLC using an extension cable.

•

The number of occupied I/O points is "8 (either input or output)  Number of
connected remote I/O points".
The total number of I/O points including extended points must not exceed 128 points for the
FX

1N

 Series or 256 points for the FX

2N

 or FX

2NC

 Series.

•

The FX

2N

-64CL-M consumes 190 mA at 5V DC.

The total current consumption at 5V for special blocks connected to the PLC must not
exceed the 5 V power capacity of the main and extension units.
When connecting to the FX

1N

 Series PLC, a maximum of two FX

2N

-64CL-M can be

connected to each of the main and extension units.

4.3

Power adapters installation concept

At least one power adapter is required per CC-Link/LT system.
When constructing a system using only one power adapter, the following three conditions
should be satisfied:

1) Total current consumption of remote I/O units, I/O equipment and master unit receiving

power from power adapter 

≤

 5 A

2) To operate the system in a stable environment, the voltage drop should be equivalent to or

less than 3.6V.

3) Because the minimum operating voltage of each remote I/O unit connected to the power

adapter is 20.4 V, therefore, Supply voltage to power adapter - Voltage drop 

≥

 20.4 V

If the total current consumption or voltage drop is large, the power adapter position should be
changed or additional power adapters should be installed.
For further details, refer to the "CL1PAD1 (Power Adapter) USER'S MANUAL (Detailed
Volume)" offered separately.

4.4

Power adapter installation condition

For further details on power adapter installation conditions, refer to the "CL1PAD1 (Power
Adapter) USER'S MANUAL (Detailed Volume)" offered separately.
The conditions for installing power adapters to the CC-Link/LT system depend on connected
equipment and wiring length.

Applicable PLC

FX

1N

/FX

2N

/FX

2NC

 Series PLC 

(FX

2NC

-CNV-IF is required when FX

2NC

 Series PLC is connected.)

Number of connectable 
master blocks

FX

1N

 Series: Up to 4

FX

2N

 Series: Up to 8

FX

2NC

 Series: Up to 3

Содержание MELSEC FX2N-64CL-M











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды