Mitsubishi Electric MELSEC FX2N-32DP-IF Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 54

background image

FX2N-32DP-IF Profibus-DP Interface Unit

Mounting and Wiring 2

2-5

2.2

Caution for Wiring

1) Do not lay signal cable near to either high voltage power cabling or cabinet housing along

the same trunking duct. Effects of noise or surge induction may occur. Keep signal cables of
more than 100 mm (3.94") from these power cables.

2) Ground the shield wire or the shield of a cable at one point on the module. Do not, however,

ground at the same point as high voltage lines.

3) Cut off all phases of power source before installation or performing wiring work in order to

avoid electric shock or damage to the product.

4) Replace the provided terminal cover before supplying power and operating the unit after

installation or wiring work, in order to avoid electric shock.

5) To connect the 32DP-IF to a Profibus-DP network should be used only the Profibus

connectors and shielded twisted-pair cable complying with EN50170.

6) The power supply of the extension units/blocks and the special function units/blocks should

be starting-up at the same time or earlier than it with 32DP-IF.

7) DO NOT use the “

●

” terminal of the 32DP-IF.

8) “24+” and “24-” terminal are not reversible.

If “24+” and “24-” terminal are reversed, the units/block may be serious damaged.

«
...
23
24
25
26
27
...
»

Содержание MELSEC FX2N-32DP-IF























































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC FX2N-32DP-IF

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Ohsung Electronics Страницы: 18

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: Caen Страницы: 20

Бренд: Parker Страницы: 44

Бренд: Gascat Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды