Mitsubishi Electric MELSEC FX2N-32DP-IF Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 54

background image

Diagnostics 5

5-1

5.

Diagnostics

5.1

Preliminary Checks

1) Check “POWER LED”. If this is OFF, please see section 5.2.

2) Check that the slave address is the same at the 32DP-IF and the DP-master configuration.

If the slave address is not the same in the 32DP-IF and in the DP-master, change this
address to match in both modules.

3) Check that the parameter data of 32DP-IF are set correctly in the DP-master.

If the parameter data of the 32DP-IF are not set correctly in the DP-master, communication
over the Profibus-DP network may be affected.

4) Check whether the network wiring and/or the cables for the extension blocks/units are

properly connected to the 32DP-IF.

5) Check that the system configuration rules have not been exceeded, i.e. the number of

special function blocks does not exceed 8 and control I/O of 32DP-IF is 256 or less.

6) Put RUN/STOP switch on the 32DP-IF into RUN.

FX2N-32DP-IF Profibus-DP Interface Unit

«
...
41
42
43
44
45
...
»

Содержание MELSEC FX2N-32DP-IF























































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC FX2N-32DP-IF

Бренд: FrSky Страницы: 2

Бренд: Idesco Страницы: 11

Бренд: B meters Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Hanwell Страницы: 34

Бренд: HANSONG Страницы: 11

Бренд: Datapath Страницы: 12

Бренд: Hansen Страницы: 4

Бренд: OES Страницы: 3

Бренд: T&D Страницы: 2

Бренд: T&S Страницы: 5

Бренд: brel-motors Страницы: 2

Бренд: GADGETMONSTER Страницы: 30

Бренд: M-system Страницы: 10

SUPERSTAR E-3000/F2

Бренд: praher Страницы: 10

Бренд: IDEC Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды