background image

When installing

Do not install in the following types of location, as this may cause malfunction.

Locations where the temperature could be lower than  0˚C or higher than 40˚C.
Locations where the humidity could be lower than 5%RH or higher than 95%RH.
Locations where the unit may come into direct contact with water.
Locations where the unit is under direct or strong sunlight. (May cause sensor to malfunction.)
Locations where there is a lot of condensation.
Locations where corrosive, neutral, or reductive gases are present.

Locations where salt damage may occur.

Vehicles (incl. vessels, trains.)

Installation location





Install the unit somewhere easy to use, as shown below.
If the unit is installed too low, water may get on it when the floor is being cleaned.
If water gets inside, it may damage the unit or moisten the sound-absorbent material, leading to bacterial growth.

The left side of the unit must be at least 150 mm away from any walls, as that is where the power switch is located.

Ensure there are no mirrors or walls near the right side, as drops of water may splash when drying hands.
 (We recommend a distance of at least 100 mm.)

Avoid locations where people or doors might bump into the unit.

Choose a completely flat surface on the wall to install the unit.

If the wall is not concrete, reinforce it before installation.

Avoid to install the unit any place where foods, tableware, or the likes are handled nearby because water may 
splash.

Do not embed the unit in the wall.

Make sure to secure distances larger than those listed below away from walls of building, etc.

Location

Clearance

Top

Left

Right

Front

Rear

Bottom

Open

150mm

100mm

Open

140mm

Rear face

hand dryer

Right face

Bottom face

Left face

100

150

140

Unit (mm)

Power controll section

Drain tank

Front panel

Unit

Installation panel screw

Installation panel

Check lamp

Heater lamp

Heater switch

Power lamp

Display

Front panel 

mounting screws

Power switch

Air speed
knob

Recommended installation heights:
Men: 940 mm 
Women: 920 mm

3

-

+

OFF

ON

OFF

ON

Power

Air sp

eed

Heater

JT-SB116EH-W-CA-IM_874HD7001-GB    06.12.9  2:13  PM    ページ 8

Содержание JT-SB116EH-W-CA









Отзывы: