Mitsubishi Electric FX2N-485-BD Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 65

background image

7.5.2

Operations

The following operations are performed in the system configuration above.

➀

The input points X000 to X003 (M1000 to M1003) in the master station are output to the output points Y010 to
Y013 in the stations Nos. 1 and 2.

➁

The input points X000 to X003 (M1064 to M1067) in the station No. 1 are output to the output points Y014 to
Y017 in the master station and the station No. 2.

➂

The input points X000 to X003 (M1128 to M1131) in the station No. 2 are output to the output points Y020 to
Y023 in the master station and the station No. 1.

➃

The data register D1 in the master station is specified as the set value of the counter C1 in the station No. 1.
The contact (M1070) status of the counter C1 is reflected on the output point Y005 in the master station.

➄

The data register D2 in the master station is specified as the set value of the counter C2 in the station No. 2.
The contact (M1140) status of the counter C2 is reflected on the output point Y006 in the master station.

➅

The value of the data register D10 in the station No. 1 and the value of the data register D20 in the station No.
2 are added in the master station, and saved to the data register D3.

➆

The value of the data register D0 in the master station and the value of the data register D20 in the station No.
2 are added in the station No. 1, and saved to the data register D11.

➇

The value of the data register D0 in the master station and the value of the data register D10 in the station No.
1 are added in the station No. 2, and saved to the data register D21.

7

FX

2N

-485-BD COMMUNICATION BOARD

N:N NETWORK

7-11

«
...
46
47
48
49
50
...
»

Содержание FX2N-485-BD


































































Отзывы:

Нет отзывов

Похожие инструкции для FX2N-485-BD

Бренд: Falcon Страницы: 3

Бренд: OBaby Страницы: 47

Бренд: FAAC Страницы: 12

Бренд: Eaton Страницы: 16

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Yardney Страницы: 8

Бренд: GBD Страницы: 15

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Koer Страницы: 6

Бренд: Samson Страницы: 102

Бренд: Seiko Страницы: 30

ASC G Wi-Fi kit

Бренд: Waeco Страницы: 386

Бренд: knorr-baby Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды