Mitsubishi Electric CR800 Series Скачать руководство пользователя страница 135

Страница: 135 / 156

4Software

List of commands 4-122

4 Software
4.1 List of commands

The available new functions in MELFA-BASIC VI are given in

Table 4-1

Table 4-1 ： List of MELFA-BASIC VI commands

Type

Class

Function

Input format (example)

Structured
program

ming

Function procedure

Defines the Function procedure.
Function procedure summarizes a series of processing enclosed by
the Function statement and the FEnd statement.

Function M Func(M1, M2)
   M3=M1+M2
   Func=M3
   Exit Function
FEnd

Library
function

#Include statement

Reads the designated program.

#Include "PRG1"

Position
and opera

tion control

Interpolation
operation

Moves to the multiple designated positions with the designated
interpolation operations and options.

Move L, P1, P2, P3, Spd=50

Joint interpolation

Moves to the designated position with joint interpolation.

Mov P1

Linear interpolation

Moves to the designated position with linear interpolation.

Mvs P1

Circular interpolation

Moves along a designated arc (start point → passing point → start
point (end point)) with 3-dimensional circular interpolation (360
degrees).

Mvc P1,P2,P1

Moves along a designated arc (start point → passing point → end
point) with 3-dimensional circular interpolation.

Mvr P1,P2,P3

Moves along the arc on the opposite side of a designated arc (start
point → reference point → end point) with 3-dimensional circular
interpolation.

Mvr2 P1,P9,P3

Moves along a set arc (start point → end point) with 3-dimensional
circular interpolation.

Mvr3 P1,P9,P3

Speed designation

Designates the speed for various interpolation operations with a
percentage (0.1% unit).

Ovrd 100

Designate the speed for joint interpolation operation with a per

centage
(0.1% unit).

JOvrd 100

Designates the speed for linear and circular interpolation with a
numerical value (mm/s unit).

Spd 123.5

Designates the acceleration/deceleration time as a percentage in
respect to the predetermined maximum acceleration/deceleration.
(1% unit)

Accel 50,80

Automatically adjusts the acceleration/deceleration according to
the parameter setting value.

Oadl ON

Sets the hand and work conditions for automatic adjustment of the
acceleration/deceleration.

Loadset 1,1

Operation

Adds a process unconditionally to the operation.

Wth

Adds a process conditionally to the operation.

WthIf

Designates smooth operation.

Cnt 1,100,200

Performance of movement is upgraded corresponding to the appli

cation.

MvTune 4

Designates the positioning completion conditions with a No. of
pulses.

Fine 200

Designates the positioning completion conditions with a distance in
a straight line

Fine 1, P

Turns the servo power ON/OFF for all axes.

Servo OFF

Limits the operation of each axis so that the designated torque is
not exceeded.

Torq 4,10

Position control

Designates the base conversion data.

Base P1

Designates the tool conversion data.

Tool P1

Float control

The robot arm rigidity is lowered and softened. (XYZ coordinate
system)

Cmp Pos ,&B00000011

The robot arm rigidity is lowered and softened. (JOINT coordinate
system)

Cmp Jnt ,&B00000011

The robot arm rigidity is lowered and softened. (TOOL coordinate
system)

Cmp Tool ,&B00000011

The robot arm rigidity is returned to the normal state.

Cmp Off

The robot arm rigidity is designated.

CmpG
1.0,1.0,1.0,1.0,1.0,1.0,1.0,1.0

Содержание CR800 Series




























































































































































Результаты поиска

Содержание CR800 Series

Отзывы:

Mitsubishi Electric CR800 Series, Специальные технические характеристики, Страница: 135 / 156

Результаты поиска

Содержание CR800 Series

Отзывы: