Mitsubishi Electric Climaveneta i-BX 010-035T, Инструкция по установке, эксплуатации и обслуживанию

Страница: 68 / 80

SYSTEM CONFIGURATION
U I A
System number 2
Parameter configuration
For systems with high temperature zone (example bathroom radiators) managed using a thermostat not supplied by Manufacturer, set the
HEATING compensation curve, parameter 0159, to a value so as to reach a suitable outlet temperature for radiators.
The mixed zone is managed according to the compensation curve set for parameter 0174.
* obligatory values for the present configuration
Description Menu
Parameter
no.
Default Write set value UOM
Select system configuration
Enable zone management
NOT = Disabled
YES = Enabled
Mn01 016A NOT YES -
System type (table 1) Mn01 0101 0 2* -
Mixing valve ZONE 1
Type of mixing valve
1= 0-10V
Mn01 012T 0-10
HEATING compensation curve ZONE 1
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0167 NOT
Heating compensation curve number Mn01 0174 0,7
Enable room temperature influence
NOT = Disabled
YES = Enabled
Mn01 0178 NOT
Room Authority Mn01 0179 30 %
MINIMUM set point limit for curve Mn01 0180 23 °C
MAXIMUM set point limit for curve Mn01 0181 45 °C
COOLING compensation curve ZONE 1
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0169 NOT
Maximum temperature set point limit in cooling mode (Tm1) Mn01 0132 20 °C
Minimum outside temperature corresponding to max. outlet
temperature (Te1)
Mn01 0133 23 °C
Minimum temperature set point limit in cooling mode (Tm2) Mn01 0134 18 °C
Maximum outside temperature corresponding to min. outlet
temperature (Te2)
Mn01 0135 36 °C
HUMIDITY CONTROL ZONE 1
Enable compensation for room humidity, ZONE LT1
NOT = Disabled
YES = Enabled
Mn01 0171 NOT
Room relative humidity value to start increasing water temperature
set point
Mn01 0172 70 %
Maximum temperature hysteresis corresponding to 100%
relative humidity
Mn01 0173 15 °C
Enable contact HL1 as DEHUMIDIFIER (The contact closes and the
dehumidifier is activated when the humidity measured by the probe
on the A5 room controller exceeds the value set for parameter 0172)
Mn01 015A DEHUMIDIFIER
HEATING compensation curve for HEAT PUMP MODE (THE TEMPERATURES MUST DIFFER FROM THOSE IN ZONE 1 & 2 BY AT
LEAST +3°C IN HEATING AND -3°C IN COOLING)
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0152 NOT -
Compensation curve number Mn01 0159 1 -
Enable room temperature influence
NOT = Disabled
YES = Enabled
Mn01 0163 NOT -
Room Authority Mn01 0164 30 %
MINIMUM set point limit curve Mn01 0165 30 °C
MAXIMUM set point limit curve Mn01 0166 48 °C
COOLING compensation curve for HEAT PUMP MODE (THE TEMPERATURES MUST DIFFER FROM THOSE IN ZONE 1 & 2 BY AT
LEAST +3°C IN HEATING AND -3°C IN COOLING)
Enable compensation curve NOT = Disabled YES = Enabled Mn01 0154 NOT -
Maximum temperature set point limit in cooling mode (Tm1) Mn01 0128 20 °C
Minimum outside temperature corresponding to max. outlet
temperature (Te1)
Mn01 0129 23 °C
Minimum temperature set point limit in cooling mode (Tm2) Mn01 0130 18 °C
Maximum outside temperature corresponding to min. outlet
temperature (Te2)
Mn01 0131 36 °C
Device address setting
ZONE 1 Room control unit address setting addr 1 14
i-BX-(Y)_i-BX-N-(Y) EN 68