background image

26MT-SP Multi-Tool

10

Original Instructions Version June 16

Avoid Noise Problems

Check and follow the local regulations for sound levels and hours of operation for garden 
machinery.
In general, operate Multi-Tools between 8 am and 5 pm on week days and 9 am to 5 pm at 
weekends.
Avoid using the Multi-Tool late at night and/or early in the morning.

 

Safety when using the Multi-Tool

When using the Multi-Tool, grip the handles firmly with both hands, place your feet slightly apart 
so your weight is distributed evenly across both legs, and always maintain a steady even posture 
while working.  Do not use on ladders or if the ground surface is slippery or uneven.  Never 
attempt to cut directly overhead or with one hand.

• Maintain full engine speed when cutting.
• Never allow other persons to come within the work area as doing so 
   might expose them to danger.
• Keep work area clear of all persons, particularly small children and pets. 
   Injury may result from flying debris.
• If grass or other objects get caught in the Multi-Tool during operation, 
   always stop the engine before removing the object.

• Never touch the spark plug or plug HT cable while the engine is in 
   operation, doing so may result in an electrical shock. 
• Never touch the exhaust, spark plug, or any metallic parts while the 
   engine is in operation or immediately after shutting down the engine. 
   These parts reach high temperatures during operation and doing so 
   could result in serious burns.

• When you finish cutting in one location and wish to continue work in another area, stop the  
   engine and fit the blade safety guards.  
• Always remove fuel from the fuel tank before transportation to prevent fuel spillage.
• Never leave the Multi-Tool exposed to direct sunlight as this can heat the fuel tank and may     
   cause a discharge of fuel, and flood the engine. 
• Be careful not to hit the cutting head against stones or the ground. 

Содержание 26MT-SP





















































Отзывы: