background image

5

1.13.

Moving parts are exposed when the cover is removed.

1.14.

Ensure all electrical connections are tight, to prevent overheating.

2. Caution!

2.1

.

Read all of these instructions and retain this guide for later use.

2.2.

Pass on this guide in the event of change of ownership of the installation site.

2.3.

Follow all warnings, cautions and instructions contained in this guide.

2.4.

Follow all warnings, cautions and instructions contained on or inside the Mira
Extreme.

2.5

.

The electrical installation must comply with the “Requirements for Electrical
Installations”

 

commonly referred to as the IEE Wiring Regulations, or any

particular regulations and practices specified by the local electricity supply
company, in force at the time of installation. The installation should be carried
out by an electrician or contractor who is registered or is a member of an
association such as:

2.5.1.

National Inspection Council for Electrical Installation and Contracting
(NICEIC), throughout the UK.

2.5.2.

The Electrical Contractors Association (ECA), England and Wales.

2.5.3.

The Electrical Contractors Association of Scotland (ECAS).

2.6.

The plumbing installation must comply with Water Supply Regulations/Bye-
laws (Scotland), Building Regulations or any particular regulations and
practices, specified by the local water company or water undertakers. The
installation should be carried out by a plumber or contractor who is registered,
or is a member of, an association such as:

2.6.1.

Institute of Plumbing (IOP), throughout the UK.

2.6.2.

National Association of Plumbing, Heating and Mechanical Services
Contractors (NAPH & MSC), England and Wales.

2.6.3.

Scottish and Northern Ireland Plumbing Employers’ Federation
(SNIPEF), Scotland and Northern Ireland.

2.7.

Anyone who may have difficulty understanding or operating the controls of any
shower should be attended whilst showering. Particular consideration should
be given to the young, the elderly, the infirm, or anyone inexperienced in the
correct operation of the controls.

2.8.

When the Mira Extreme has reached the end of its serviceable life, it should
be disposed of in a safe manner, in accordance with current local authority
recycling, or waste disposal policy.

Содержание Extreme Thermostatic













































Отзывы: