MIOX RIO H1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 82

MIOX RIO H1 Скачать руководство пользователя страница 15

MIOX RIO Series Operators Manual

P/N: 102-00076-G

Page 14

Receiving and Unpacking the RIO Series OSG

Your RIO Series OSG has been carefully packed to avoid shipping and handling damage. The
OSG enclosures are shipped in crated pallets. Brine generator tanks, oxidant tanks, water
softeners, and other ancillary equipment are also shipped on pallets. To safely unpack your OSG,
complete the following steps:

1.

Unpack the OSG enclosure -

Remove the crate from around the enclosure.

Check the enclosure for any damage that may have occurred during shipping.

2.

Unpack Installation Kits -

Remove the contents from the brine generator and

oxidant storage tanks. These items include the OSG installation kit, the solution
tank level switch, the softener installation kit, and the solution tank drop tube.

3.

Unpack the water softener -

Remove the water softener towers from their

packaging. Do not turn the softeners over or lay them on their sides as this will
disturb the softening resin and gravel beds inside the softener and affect softener
performance.

4.

Unpack all other equipment -

Remove any optional components (heaters,

chillers, injection systems, etc.) from their packaging and inspect for damage.

After completing a visual inspection, compare ordered items against what was delivered. Should
you find anything damaged or missing, please contact your MIOX sales agent or MIOX Customer
Service.

Securing the Cabinet

The RIO Series OSG is designed with mounting feet and holes for securing the enclosure to the
floor. While there are no vibrational components that would cause the system to move, good
seismic design practice and building codes in some areas require that the unit be secured to the
floor. Concrete anchors or other suitable hardware is recommended to secure the RIO OSG to
the floor. Consult local seismic codes for site-specific requirements.

«
...
13
14
15
16
17
...
»

Содержание RIO H1



















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды