Minolta CF1501 Скачать руководство пользователя страница 95

Страница: 95 / 270

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-80

18-15. Waste Toner Near Full and Full Detecting Mechanism

• Waste toner near full and full conditions are detected.

1. Waste Toner Near Full
• The Waste Toner Full Detecting Sensor is used to detect a waste toner near full condi-

tion.

• When the sensor is blocked by the toner collected in the bottle, the copier determines

that it is a waste toner near full condition.

• A reflector type sensor is used.

4004M057AA

Waste Toner Full Detecting Sensor (PC29)

Toner Collecting Bottle

4004M603AA

Waste Toner Full
Detecting Sensor
(PC29)

Waste Toner

Before Waste Toner Near
Full Condition is Detected

When Waste Toner Near
Full Condition is Detected

Содержание CF1501















































































































































































































































































Результаты поиска

Содержание CF1501

Отзывы:

Бренды по названию

Популярные бренды

Minolta CF1501, Руководство по обслуживанию

Результаты поиска

Содержание CF1501

Отзывы:

Бренды по названию

Популярные бренды