manualshive.com logo in svg

Minolta CF1501, Руководство по обслуживанию

Поделиться
Скачать
Minolta CF1501 Скачать руководство пользователя страница 212

FrameMaker Ver.5.5E(PC)  CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-80

(10) Fuser Temp.

This adjustment must be made in the following case:

• Fusing performance is poor or offset occurs when the paper type or environmental condi-

tions are changed.

As a general rule, the following settings should not be changed:

• Plain (Lower)
• OHP Film (Lower)
• Thick 1 (Lower)
• Thick 2 (Lower)

Adjustment Procedure
1. Call the Tech. Rep. Mode to the screen.
2. Touch these keys in this order: “Machine Adjust” 

→

 “Fuse Temp.”

3. Select the paper type.
4. Press the Clear key to clear the current setting.
5. Enter the new setting from the 10-Key Pad.

✽

Use the Access key to select the sign of + or -.

Adjustment Instructions

If fusing performance is poor, increase the setting.
If offset occurs, decrease the setting.

✽

The temperature does not change immediately when the setting is change.  Wait a while 
before performing the subsequent steps.

6. Touch “MENU.”
7. Go back to the Basic screen.
8. Make an ordinary copy using the paper type selected in step 3.
9. Check the image on the copy to ensure that there are no image problems evident.
10. If fusing performance is still poor or offset is evident, change the setting and make a 

check again.

Содержание CF1501















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды