Minolta CF1501 Скачать руководство пользователя страница 176

Страница: 176 / 270

FrameMaker Ver.5.5E(PC) CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-44

(13) Removal of the Fusing Pressure/Retraction Motor

1. Remove the MSC/PIC Board Box.

☞

D-41 (steps 1 through 8)

2. Remove the Fusing Drive Motor.

3. Remove two screws and the harness holder.

4004D063AA

4. Unplug two connectors.
5. Remove three screws and the Fusing Pressure/

Retraction Motor Assy.

4004D064AA

6. Snap off one E-ring and remove the gear and pin.

NOTE

• Use care not to lose the pin.

7. Snap off one E-ring and remove the bushing.
8. Remove two screws and the Fusing Retraction

Position Sensor mounting bracket.

4004D125AA

9. Remove the gear (black).

4004D209AA

10. Remove two screws and the Fusing Pressure/

Retraction Motor.

4004D126AB

Содержание CF1501















































































































































































































































































Результаты поиска

Содержание CF1501

Отзывы:

Бренды по названию

Популярные бренды

Minolta CF1501, Руководство по обслуживанию

Результаты поиска

Содержание CF1501

Отзывы:

Бренды по названию

Популярные бренды