MINOLTA-QMS magicolor 330 Скачать руководство пользователя страница 91

Страница: 91 / 132

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-87

DRP 7.20 Feed Solenoid (PL22.2.21)

Use this procedure to remove and replace the Feed Solenoid for OPT1 Tray, OPT2 Tray, or OPT3 Tray of the
LCIF.

Removal

1. Remove the LCIF Motor Assembly (DRP 7.11).

2. Free the Feed Solenoid wire harness from the harness clip.

3. Remove the screw securing the Feed Solenoid to the LCIF frame.

4. Push down on the Feed Solenoid arm and remove the Solenoid from the LCIF frame.

Replacement

1. Position the Feed Solenoid as shown in the illustration.

2. Push down on the Feed Solenoid arm as you reinstall the Solenoid onto the LCIF frame.

3. Line up the three holes in the Solenoid with the screw hole and two positioning tabs on the frame.

4. Use one screw to secure the Feed Solenoid to the LCIF frame.

5. Secure the Feed Solenoid wire harness to the harness clip.

6. Reinstall the LCIF Motor Assembly (DRP 7.11).

Содержание magicolor 330





































































































































Результаты поиска

Содержание magicolor 330

Отзывы:

Похожие инструкции для magicolor 330

Бренды по названию

Популярные бренды

MINOLTA-QMS magicolor 330, Руководство по обслуживанию

Результаты поиска

Содержание magicolor 330

Отзывы:

Похожие инструкции для magicolor 330

Бренды по названию

Популярные бренды