MINOLTA-QMS magicolor 330 Скачать руководство пользователя страница 75

Страница: 75 / 132

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-71

DRP 7.12 LCIF Motor Assembly (PL22.1.5)

Removal

1. Remove the Cover Bracket (DRP 7.4).

2. Remove the Feeder PWB (DRP 7.10).

3. Free the Feed Solenoid and Sensor wires from the three wire clips that are attached to the front of the

Motor Assembly

4. Loosen, but do not remove, the two screws securing the bottom of the Motor Assembly to the LCIF frame.

5. Remove the two screws securing the top of the Motor Assembly to the LCIF frame and remove the Assem-

bly.

6. Pull the Feed Solenoid and Sensor wires through the grommet holes in the Assembly.

Replacement

1. Insert the Feed Solenoid and Sensor wires through the grommet holes in the LCIF Motor Assembly.

Insert OPT1 Tray wires through the top hole, OPT2 Tray wires through the middle hole, and OPT3 Tray
wires through the bottom hole.

2. Slide the bottom of the LCIF Motor Assembly behind the two loosened screws that are located at the bot-

tom of the LCIF frame.

3. Reposition the LCIF Motor Assembly so the top two screw holes in the Assembly line up with the top two

screw holes in the LCIF frame.

4. Use two screws to secure the top of the LCIF Motor Assembly to the LCIF frame.

5. Tighten the two bottom screws to secure the bottom of the LCIF Motor Assembly to the LCIF frame.

6. Secure the Feed Solenoid and Sensor wires into the three wire clips that are attached to the front of the

Motor Assembly

7. Reinstall the Feeder PWB (DRP 7.10).

8. Reinstall the Cover Bracket (DRP 7.4).

Содержание magicolor 330





































































































































Результаты поиска

Содержание magicolor 330

Отзывы:

Бренды по названию

Популярные бренды

MINOLTA-QMS magicolor 330, Руководство по обслуживанию

Результаты поиска

Содержание magicolor 330

Отзывы:

Бренды по названию

Популярные бренды