MINOLTA-QMS magicolor 330 Скачать руководство пользователя страница 107

Страница: 107 / 132

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-103

9.1

Using the Parts List

1. The numbers shown in each illustration correspond to the parts list number for that illustration.

2. Throughout this manual, parts are identified by the prefix “PL”, followed by a number, a decimal point, and

another number. For example, PL3.12 means the part is item 12 of Parts List 3.

3. The capital letters “C”, “E”, “KL”, and “S” shown in an illustration stand for C-ring, E-ring, Clamp, and

Screw, respectively.

4. A shaded triangl

▼

in an illustration indicates the item is part of an assembly.

5. The notation “with X~Y” following an part name indicates an assembly that is made up of components X

through Y. For example, “1 (with 2~4)” means part 1 consists of part 2, part 3, and part 4.

6. The symbol

following a part name indicates the part is an FX Recommended Part and is constantly

stocked and readily available. Other parts may be stocked according to the needs of each individual OEM
client.

7. An asterisk

following a part name indicates the page contains a note about this part.

8. The notation “J1<>J2 and P2” is attached to a wire harness. It indicates that connector jack 1 is attached

to one end of the wire harness and connector jack 2 is attached to the other end that is plugged into plug 2.

Содержание magicolor 330





































































































































Результаты поиска

Содержание magicolor 330

Отзывы:

Похожие инструкции для magicolor 330

Бренды по названию

Популярные бренды

MINOLTA-QMS magicolor 330, Руководство по обслуживанию

Результаты поиска

Содержание magicolor 330

Отзывы:

Похожие инструкции для magicolor 330

Бренды по названию

Популярные бренды