manualshive.com logo in svg

MINOLTA-QMS magicolor 330, Руководство по обслуживанию

Поделиться
Скачать
MINOLTA-QMS magicolor 330 Скачать руководство пользователя страница 83

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-79

DRP 7.16 LCIF Drive Assembly (PL22.1.1)

Use this procedure to remove and replace the LCIF Drive Assembly for OPT1 Tray, OPT2 Tray, or OPT3 Tray of
the LCIF.

Removal

1. Remove the Tray from the LCIF.

2. Remove the Right Cover (DRP 7.6).

3. Remove the LCIF Motor Assembly (DRP 7.11).

4. Remove the two screws securing the Tray Stopper to the LCIF frame and remove the Stopper (Figure 1).

5. Remove any wire harnesses that are attached to the Drive Assembly.

6. Remove the screw securing the LCIF Drive Assembly to the front-right of the LCIF frame (Figure 2).

7. Pull the LCIF Drive Assembly to the front of the LCIF so the rear locating pin of the Drive Assembly is freed

from the locating hole in the frame, and remove the Assembly out through the empty paper feeder.

Replacement

1. Reinstall the LCIF Drive Assembly by inserting the rear locating pin of the Assembly into the corresponding

locating in the rear of the LCIF frame.

2. Position the front of the LCIF Drive Assembly so the screw hole and locating tab in the Assembly line up

with the screw hole and locating hole in the front of the LCIF Frame.

3. Use one screw to secure the LCIF Drive Assembly to the front-right of the LCIF frame.

4. Reinstall any wire harnesses that were attached to the Drive Assembly.

5. Reinstall the Tray Stopper to the LCIF frame and use two screws to secure the Stopper.

6. Reinstall the LCIF Motor Assembly (DRP 7.11).

7. Reinstall the Right Cover (DRP 7.6).

8. Reinstall the Tray.

Содержание magicolor 330





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды