manualshive.com logo in svg

MINOLTA-QMS magicolor 330, Руководство по обслуживанию

Поделиться
Скачать
MINOLTA-QMS magicolor 330 Скачать руководство пользователя страница 37

magicolor 330 Large-Capacity Input Feeder Service Manual

LCIF-33

4.7

Error Message: Feeder Cover Missing

There is a problem with the Large Capacity Input  Feeder Cover.

Logic control on the MCU PWB detected that LCIF Cover Interlock Switch circuit is open.

Step

Actions and Question

Yes

No

SUSPECT COMPONENTS
The following components are associated with this specific
problem. One or more of these components may have failed
partially or completely. If you cannot isolate the problem using
this FIP, replace each component listed below, one at a time,
until the problem disappears.

• Wiring and connectors linking the components

1

LCIF FEEDER COVER RESEAT

1. Open the Feeder Cover.

2. Firmly close the Feeder Cover.

Does the error message still appear?

Go to step 2

Problem
solved

2

LCIF FEEDER COVER SWITCH INSPECTION

1. Open the Feeder Cover.

2. Inspect the Feeder Cover Switch actuators that are located

near the top-rear and top-front of the Cover.

Are the actuators intact and free of damage?

Go to step 3

Replace the 
LCIF Cover 
Assembly 
(LCIF DRP 
6.8)

3

LCIF FEEDER COVER SWITCH TEST

1. Enter Diagnostics and run the LCIF Cover Interlock Switch

input test.

2. Close the Feeder Cover.

3. Observe the last number in the Diagnostic Status Window.

4. Open the Feeder Cover.

Does the last number in the Diagnostic Status Window 
change from 00 to 01, when you open the LCIF Feede
Cover?

Go to step 5

Go to step 4

4

Replace both Feeder Cover Switches  (LCIF DRP 6.14)

Does the error message still appear?

Go to step 5

Problem
Solved

5

Replace the Feeder PWB (LCIF DRP 6.10)

Does the error message still appear?

Replace the
MCU PWB
(Base Engine
DRP 6.123)

Problem
Solved

Содержание magicolor 330





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды