MINOLTA-QMS ENord magicolor 3100 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 204

MINOLTA-QMS ENord magicolor 3100 Скачать руководство пользователя страница 59

Duplexing

53

Duplexing

Select paper with high opacity for duplex (2-sided) printing. Opacity refers to
how effectively paper blocks out what is written on the opposite side of the
page. If the paper has low opacity (high translucency), then the printed data
from one side of the page will show through to the other side. For best results,
print a small quantity to make sure the opacity is acceptable.

5

"

Only up to 28 lb bond (105 g/m²) plain paper can be autoduplexed.

How do I manually duplex?

5

"

Media jams may occur if the printed sheet(s) reinserted are not
entirely flat.

1

In the printer driver (Paper tab), select Simplex, then double-click OK.

2

In the Print Document screen, select All.

3

Select and print the Odd-Numbered Pages.

4

Remove the media, flip it over, and select and print the Even-Numbered
Pages.

How do I autoduplex?

Your printer is configured with 256 MB of RAM. Duplex (2-sided) printing can
be done automatically with enough memory installed. For example, a Fine
print quality, 1200 dpi duplex legal-size page would require 288 MB of
SDRAM. Additional memory can be added up to 512 MB. Very high coverage
pages may revert to 600 dpi when duplex printing if enough memory is not
installed. With letter media, two sheets are in the media path; with legal, only
one is. Therefore, it requires more memory to print the two sheets of letter
media.

Duplexing envelopes, glossy stock heavier than 28 lb bond (105 g/m

2

), labels,

postcards, thick stock heavier than 28 lb bond (105 g/m

2

), transfer media, or

transparencies is not supported.

1

To print duplex (both sides of the sheet), load the media with the top of
the media toward the back of the tray. When printing from the

„

Upper or optional trays, load the media printing-side up.

„

Multipurpose tray, load the media printing-side down.

In autoduplexing, the back side is printed first and the front side is
printed last.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

«
...
57
58
59
60
61
...
»

Содержание ENord magicolor 3100













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды