manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, Руководство пользователя

Поделиться
Скачать
MINOLTA-QMS ENord magicolor 3100 Скачать руководство пользователя страница 107

Status, Error, and Service Messages 

101

INVALID IMAGING 

UNIT

The printer has 
detected a 
nongenuine 
MINOLTA-QMS 
imaging unit. 

To resume printing and 
to prevent permanent 
damage to your 
MINOLTA-QMS printer, 
replace the imaging unit 
with a genuine 
MINOLTA-QMS imaging 
unit. If you are using a 
genuine MINOLTA-QMS 
imaging unit and still 
receive this error, 
contact Support. Refer 
to the 

Service & Support 

Guide 

or check 

www.minolta-qms.com/
support. 

MEDIA JAM DUPLEX

Media has jammed in 
the duplexer.

Locate and remove the 
jam. Open and close the 
front door to reset the 
printer.

MEDIA JAM FEED

Media has jammed 
while being pulled 
from the specified 
tray.

MEDIA JAM FUSER

Media has jammed 
leaving the fuser 
area.

MEDIA JAM 

REGISTRATION

Media has jammed in 
front of the imaging 
unit.

MEDIA TYPE 

MISMATCH

The media detected 
in the tray doesn’t 
match the media size 
or type setting.

Change the media in the 
tray or change the 
media size or type 
setting. 

MISMATCH JAM

Media has jammed 
near the 
transparency sensor.

Locate and remove the 
jam. Open and close the 
front door to reset the 
printer.

This message...

means...

do this...

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Содержание ENord magicolor 3100













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды