MINOLTA-QMS ENord magicolor 3100 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 204

MINOLTA-QMS ENord magicolor 3100 Скачать руководство пользователя страница 100

Status, Error, and Service Messages

94

Status, Error, and Service Messages

Status, error, and service messages are displayed in the control panel
message window. They provide information about your printer and help
you locate many problems. When the condition associated with a displayed
message has changed, the message is cleared from the window. Refer to
the

CrownBooks

for further information.

5

"

Status messages are not displayed while the printer is off line.

Status and Error Messages

This message...

means...

do this...

<

COLOR

> TONER

EMPTY

The

<

COLOR

>

toner

cartridge is empty.

Replace the toner
cartridge.

Open and close the
printer’s front door.

Reset the consumables
count in the Operator
Control/Consumables/
Item Replaced/

<

COLOR

>

Toner menu.

<

COLOR

> TONER LOW

The

<

COLOR

>

toner

cartridge is low.
Printing continues
even though the
warning appears.
Approximately 100
letter/A4 pages (at
5% coverage) after
detecting that toner in
a cartridge is low, the
printer displays

<

COLOR

> TONER

EMPTY

in the

message window,
and the printer stops.

The color gradually
fades, so replace the
toner cartridge as soon
as possible.

Do not send very large
print jobs after the

TONER LOW

message is

displayed.

Reset the consumables
count in the Operator
Control/Consumables/
Item Replaced/

<

COLOR

>

Toner menu.

<

COLOR

> TONER

MISSING

The

<

COLOR

>

toner

cartridge is not
installed properly.

Install the indicated
toner cartridge.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

«
...
98
99
100
101
102
...
»

Содержание ENord magicolor 3100













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды