Mindray Accutorr V Скачать руководство пользователя страница 33

Страница: 33 / 130

Standby and Power OFF

Operation

3 - 4

0070-10-0699-02

Accutorr V Operating Instructions

3.4

Standby and Power OFF

3.4.1

Entering Standby

Press

(13) for less than 1 second to put the monitor in standby mode.

In the dialog on the LCD Display (17), confirm entering standby by pressing

(18).

3.4.2

Exiting Standby

Press any key on the device.

In the dialog on the LCD Display (17), confirm exiting standby by pressing

(18).

NOTE:

The monitor exits standby mode when it receives SpO

physiological signals or the temp probe is removed from the
sheath.

Once the monitor exits Standby mode, it enables alarms, restores all functions, restores
communication, and starts to save trend data.

3.4.3

Turning Power Off

Press

(13) for two (2) seconds or more to turn off the monitor.

NOTE:

Disconnect the Accutorr V from the mains to isolate it from
the mains power during an emergency.

3.4.4

Selecting a Configuration

When power to the Accutorr V is turned on, it automatically loads one of three
configurations.

• The

FACTORY DEFAULT

(or

FACTORY CONFIG

) is installed by the factory and

cannot be modified.

• The

USER

CONFIG

is created by following the steps in Section 3.16.5.

• The

LAST

CONFIG

consists of the parameter settings in use before the unit was

powered off.

To select a configuration to be loaded at power-on, follow the steps in Section 3.16.6.

To load a user configuration or factory default configuration after the Accutorr V is powered
on:

Press

(12) to display the SYSTEM SETUP dialog as shown in FIGURE 3-2.

Содержание Accutorr V



































































































































Результаты поиска

Содержание Accutorr V

Отзывы:

Похожие инструкции для Accutorr V

Бренды по названию

Популярные бренды

Mindray Accutorr V, Руководство по эксплуатации

Результаты поиска

Содержание Accutorr V

Отзывы:

Похожие инструкции для Accutorr V

Бренды по названию

Популярные бренды