Mindray Accutorr V Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 130

background image

Accutorr V Operating Instructions

0070-10-0699-02

6 - 7

Appendix

Specifications

Pulse Rate

Pulse Rate During No Motion
Conditions

1

:

Adult/Pediatric/Neonates:

25 – 240 BPM ±3 digits

Pulse Rate During Motion
Conditions

2,3

:

Adult/Pediatric/Neonates:

25 – 240 BPM ±5 digits

Update Rate:

1 second

Wavelength of light emitted by the
sensors

red:

660 nm

infrared

940 nm

1

The Masimo MS-2013 pulse oximeter with LNOP- Adt sensors have been validated for no motion
accuracy in human blood studies on healthy adult volunteers in induced hypoxia studies in the
range of 70% to 100% SpO

2

against a laboratory co-oximeter and ECG monitor. This variation

equals plus or minus one standard deviation. Plus or minus one standard deviation encompasses
68% of the population.

2

The Masimo MS-2013 pulse oximeter with LNOP- Adt sensors has been validated for motion accu-
racy in human blood studies on healthy adult volunteers in induced hypoxia studies while per-
forming rubbing and tapping motions at 2 to 4 Hz. At an amplitude of 1 to 2 cm and non-
repetitive motion between 1 to 5 Hz. At an amplitude of 2 to 3cm in induced hypoxia studies in
the range of 70% to 100% SpO

2

against a laboratory co-oximeter and ECG monitor. This variation

equals plus or minus one standard deviation. Plus or minus one standard deviation encompasses
68% of the population.

3

The Masimo MS-13 pulse oximeter with LNOP-Neo and Neo Pt sensors have been validated for
neonatal motion accuracy in human blood studies on neonates while moving the neonate’s foot
at 2 to 4 Hz at an amplitude of 1 to 2 cm against a laboratory co-oximeter and ECG monitor. This
variation equals plus or minus one standard deviation. Plus or minus one standard deviation
encompasses 68% of the population

4

The Masimo MS-13 pulse oximeter has been validated for low perfusion accuracy in bench top
testing against a Biotek Index 2 simulator and Masimo’s simulator with signal strengths of
greater then 0.02% and a % transmission of greater than 5% for saturation’s ranging from 70 to
100%. This variation equals plus or minus one standard deviation. Plus or minus one standard
deviation encompasses 68% of the population.

«
...
110
111
112
113
114
...
»

Содержание Accutorr V



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Accutorr V

Бренд: Labnet Страницы: 2

Бренд: Hanil Страницы: 60

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: TAIKO Audio Страницы: 24

Бренд: Bante Instruments Страницы: 6

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Farmet Страницы: 102

Бренд: iHealth Страницы: 8

Бренд: Olympus Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды