Minarik RG300 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

background image

21

Operation

Cased drives

1. Set the FORWARD/BRAKE/REVERSE switch to the

BRAKE position.

2. Set the speed adjust potentiometer to “0” (full CCW).
3. Apply AC line voltage.
4. Set the POWER switch to the ON position.
5. Set the FORWARD/BRAKE/REVERSE switch to the

desired direction of rotation.

7. Slowly advance the speed adjust potentiometer clockwise

(CW). The motor slowly accelerates as the potentiometer is
turned CW. Continue until the desired speed is reached.

8. To brake the motor, set the FORWARD/BRAKE/REVERSE

switch to the BRAKE position. To coast the motor to a stop,
set the POWER switch to the OFF position.

9. To reverse direction:

a. Set the FORWARD/BRAKE/REVERSE switch to the

BRAKE position.

b. After the motor comes to a complete stop, set the

FORWARD/BRAKE/REVERSE switch to the desired
direction of rotation.

10. Set the POWER switch to OFF to remove power from the

drive.

«
...
27
28
29
30
31
...
»

Содержание RG300 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для RG300 Series

Бренд: Fagor Страницы: 36

Бренд: Danfoss Страницы: 10

Бренд: IBM Страницы: 20

HELICAL GEAR BOXES BC Series

Бренд: BOCKWOLDT Страницы: 70

Бренд: elero Страницы: 31

Бренд: LaCie Страницы: 32

MP 7040A series

Бренд: Ricoh Страницы: 31

Бренд: Vacon Страницы: 82

Бренд: Asus Страницы: 28

Бренд: Asus Страницы: 9

Бренд: Asus Страницы: 36

Pavilion t100 - Desktop PC

Бренд: HP Страницы: 2

Бренд: HP Страницы: 2

Бренд: Samsung Страницы: 26

Бренд: Toshiba Страницы: 18

Бренд: Baldor Страницы: 220

Бренд: Leadshine Страницы: 18

Бренд: Shugart Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды