MIMAKI CJV30-100 Скачать руководство пользователя

Страница: 213 / 274

6-39

Other Maintenance Functions

Mai
ntenanc

Replacing the Waste Ink Tank with Another

When the message on the right has been displayed, check the state of
the waste ink tank immediately and replace the tank as necessary.

Remove the waste ink tank guard.

(1)

Lift the waste ink tank guard and unlock it.

(2)

Open the waste ink tank guard to your side.

Hold the grip of the waste ink tank and remove the
tank by pulling it to your side.

• Attach the cap to the removed waste ink tank.

Replace the waste ink tank with another.

(1)

Prepare a new waste ink tank (SPC-0117).

(2)

Hold the grip of the waste ink tank and insert the tank.

< LOCA L . 1 >

[ # 0 1 ]

! WAS T E T ANK

Waste ink guard

Lift and pull it.

Cap

Accumulated waste ink

New waste ink
tank

Содержание CJV30-100



















































































































































































































































































Результаты поиска

Содержание CJV30-100

Отзывы:

Похожие инструкции для CJV30-100

Бренды по названию

Популярные бренды

MIMAKI CJV30-100, Руководство по эксплуатации

Результаты поиска

Содержание CJV30-100

Отзывы:

Похожие инструкции для CJV30-100

Бренды по названию

Популярные бренды