Mikado LOGO 500 3D, Руководство пользователя

Страница: 2 / 32

Manual
The New Generation - ©Mikado Modellhubschrauber - Page 2
Speed-
controller
Index
OPERATING YOUR MODEL SAFELY
Operate the helicopter in spacious areas with no people
nearby.
!Warning: Do NOT operate the helicopter in the fol-
lowing places and situations (or else you risk severe
accidents):
• in places where children gather or people pass
through
• in residential areas and parks
• indoors and in limited space
• in windy weather or when there is any rain, snow, fog
or other precipitation
If you do not observe these instructions you may be held
reliable for personal injury or property damage!
Always check the R/C system prior to operating your
helicopter. When the R/C system batteries get weaker,
the operational range of the R/C system decreases. Note
that you may lose control of your model when operating
it under such conditions.
Keep in mind that other people around you might also
be operating a R/C model.
Never use a frequency which someone else is using at
the same time. Radio signals will be mixed and you will
lose control of your model.
If the model shows irregular behavior, bring the model
to a halt immediately. Turn off all power switches and
disconnect the batteries. Investigate the reason and fix
the problem. Do not operate the model again as long
as the problem is not solved, as this may lead to further
trouble and unforeseen accidents.
! Warning: In order to prevent accidents and personal
injury, be sure to observe the following:
Before flying the helicopter, ensure that all screws are
tightened. A single loose screw may cause a major
accident.
Replace all broken or defective parts with new ones, as
damaged parts lead to crashes.
Never approach a spinning rotor. Keep at least 10 me-
ters/yards away from a spinning rotor blades.
Do not touch the motor immediately after use. It may be
hot enough to cause burns.
Perform all necessary maintenance.
PRIOR TO ADJUSTING AND OPERATING YOUR MO-
DEL, OBSERVE THE FOLLOWING
!Warning: Operate the helicopter only outdoors and out of
people’s reach as the main rotor operates at high rpm!
! Warning: While adjusting, stand at least 10 meters/
yards away from the helicopter!
Novice R/C helicopter pilots should always seek advice
from experienced pilots to obtain hints with assembly and
for pre-flight adjustments. Note that a badly assembled
or insufficiently adjusted helicopter is a safety hazard!
In the beginning, novice R/C helicopter pilots should
always be assisted by an experienced pilot and never
fly alone!
Tools for Assembly & R/C Equipment
Radio with Heli-Software
Receiver
Fast Charger
Motor + Speed Controller (check the Mikado
webpages for recommended motors)
Alle shown products are examples. You may use different brands.
BEC, replaces
receiver battery
Scissors
Rubber Hammer
Screwdrivers
(plus and minus)
Hex Wrenches
1.5/2.0/2.5/3.0 mm
(.055/.079/.098/.118 in)
Ball
link
pliers
Threadlock
Ball
link
pliers
Grease
Pitch Gauge
Safety Instructions
Index . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Instructions . . . . . . . . . . . . . . . . . . 2
Tools for Assembly & R/C Equipment . . . . . . . . 2
1 Mainframe . . . . . . . . . . . . . . . . . . . . . 3
2 Tail Rotor & Tail Boom 500/600 DX . . . . . . . . 4
3 Tail Rotor & Tail Boom 500 3D . . . . . . . . . . . 5
4 Tail Rotor & Tail Boom 600 3D . . . . . . . . . . . 6
5 Main Gear & Tail Rotor Assembly . . . . . . . . . 7
6 Swashplate . . . . . . . . . . . . . . . . . . . . 8
7 Radio . . . . . . . . . . . . . . . . . . . . . . . 9
8 Servo Installation . . . . . . . . . . . . . . . . 10
9 Rotor Head 500 DX/3D . . . . . . . . . . . . . 11
10 Rotor Head 600 DX/3D . . . . . . . . . . . . . 12
11 V-Bar Rotor Head 500 3D . . . . . . . . . . . 13
12 V-Bar Rotor Head 600 3D . . . . . . . . . . . 14
13 Rotor Head Assembly . . . . . . . . . . . . . 15 14 Mounting the Motor . . . . . . . . . . . . . . . 15
15 Radio and Battery . . . . . . . . . . . . . . . 16
16 Decal and Canopy Mounting . . . . . . . . . . 17
17 RC Programming . . . . . . . . . . . . . . . . 18
18 Rotor Blades . . . . . . . . . . . . . . . . . . 21
19 Pre-Flight Check . . . . . . . . . . . . . . . . 21
20 Operation During Flight . . . . . . . . . . . . 22
21 Upgrades . . . . . . . . . . . . . . . . . . . . 23
22 Overview Chassis . . . . . . . . . . . . . . . 24
23 Overview Tail Rotor LOGO 500/600 DX . . . . 25
24 Overview Tail Rotor LOGO 500 3D . . . . . . . 26
25 Overview Tail Rotor LOGO 600 3D . . . . . . . 27
26 Overview Rotor Head LOGO 500 . . . . . . . 28
27 Overview Rotor Head LOGO 600 . . . . . . . 29
28 Overview V-Bar Head LOGO 500 . . . . . . . 30
29 Overview V-Bar Head LOGO 600 . . . . . . . 31
V-Bar
Manual for Mikado helicopter models LOGO 500 DX, LOGO 500 3D, LOGO 600 DX and LOGO 600 3D