Miele TXI 680 WP Скачать руководство пользователя страница 58

Страница: 58 / 96

Frequently Asked Questions

Message

Possible cause and solution



Empty container See


lights up after

a program has
been cancelled.

The condensed water container is full or there is a
kink in the drain hose.



Empty the condensed water container.



Check the drain hose.

To switch the fault message off:



Open and close the door while the dryer is
switched on or switch the dryer off and back on
again.



Fill the condensed
water container

This is to remind you that water is taken from the
condensed water container when the

SoftSteam

program is being used. The condensed water
container must be filled with water to at least the

–min–

marker.



Fill the condensed water container.

To switch off the message:



Confirm with



Open & close door

This is to remind you to load the laundry when the

SoftSteam

program is selected.



Load the laundry in the drum.



Blockage detected.
See 

lights up

after a program
has been
interrupted.

The laundry is unevenly distributed or has rolled up.



Open the door and untangle the laundry, and
remove a few items, if necessary.



Switch the dryer off and then on again.



Start a program.



 Service Fault F
XXX

lights up

after a program
has been
interrupted.

There is no obvious cause.



Switch the dryer off and then on again.



Start a program.

If the program is interrupted again and an error
message appears, there is a fault. Contact Miele
Technical Service.

Содержание TXI 680 WP

































































































Результаты поиска

Содержание TXI 680 WP

Отзывы:

Похожие инструкции для TXI 680 WP

Бренды по названию

Популярные бренды

Miele TXI 680 WP, Руководство по эксплуатации

Результаты поиска

Содержание TXI 680 WP

Отзывы:

Похожие инструкции для TXI 680 WP

Бренды по названию

Популярные бренды