manualshive.com logo in svg

Miele PG 8591, Руководство по эксплуатации

Поделиться
Скачать
Miele PG 8591 Скачать руководство пользователя страница 59

Operation

59

System messages

After the cleaning machine is switched on or a programme sequence
is completed, a series of system messages may be shown on the
display. These indicate e.g. low fill levels in the containers or required
maintenance.

Changing the
filter

Several hours before reaching the maximum permitted operation
hours, you will be prompted to change the air filters.

Fit a new HEPA filter?

Now

Later ( operating hrs.)

Confirm the message with 

OK

 and change the filter according to

the instructions in the section “Maintenance”.

Filter life remaining
10 h

The remaining operating hours for this filter type are shown on the
display.

Confirm the message with 

OK

.

Then you will be asked if you wish to reset the operating hours
counter.

The operating hours counter must only be reset when the filter

has been changed.

Reset

No

Yes

-

Yes

The operating hours counter will be reset for the new filter.

-

No

The counter will not be reset.

Select an option using the 

 and 

 arrow buttons.

Confirm your selection with 

OK

.

Содержание PG 8591

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды