Miele PG 8591 Скачать руководство пользователя страница 48

Страница: 48 / 152

Adding and dispensing chemical agents



Close the container.



Wipe up any spilled rinsing agent. This prevents over-foaming
occurring during the next programme.

Refill indicator

When the fill level is low in the (DOS 2) supply container for rinsing
agent you are reminded to refill it.

Refill rinsing agent



Confirm the message shown with

and



refill the rinsing agent as described.

Dispensing
rinsing agent

The dispensing concentration is set by the Miele Customer Service
Department.

- If there are spots of water left on load items after reprocessing, then

the dispensing concentration is set too low.

- If clouding or smearing appears on load items, the dispensing

concentration is set too high.



In either case contact the Miele Customer Service Department and
have the dispensing concentration reset.

Содержание PG 8591

























































































































































Результаты поиска

Содержание PG 8591

Отзывы:

Бренды по названию

Популярные бренды

Miele PG 8591, Руководство по эксплуатации

Результаты поиска

Содержание PG 8591

Отзывы:

Бренды по названию

Популярные бренды